India Broadband Forum

John09 · 09-19-09, 11:00 PM

I am trying to configure my vonage phone adopter using following information from this link I have followed all instructions but still my vonage device unable to connect to beetel modem.

I tried to find out beetel modem user guide and I could not find one. Is any one have soft copy of user manual.

Here is my WAN configuration in beeltel modem.

Wide Area Network (WAN) Setup

Choose Add, Edit, or Remove to configure WAN interfaces.
Choose Save/Reboot to apply the changes and reboot the system.

VPI/VCI Service Protocol State Status IP Address Remove Edit
1/32 pppoe_1_32 PPPoE Enabled Up 122.169.220.123
Your browser may not support display of this image.

0/35 br_0_35 Bridge Enabled Up
Your browser may not support display of this image.

essbebe · 09-20-09, 01:37 AM

....enter your USERID and PW in the wan page.
Enable DHCP.
Connect computer using only beetel 220BX.
After confirming all ok , then transfer the RJ45

from computer end to to Vonage
( Blue cable with only 4 connections )
Check the error messages and give feedback.
All the 3 icons should show. Telephone/Monitor Globe.
Presume you have a U.S allotted number.
vonage IP 192.168.15.
UserID: router PW: router.

Check this link for identical modem pages.
h t t p ://mydataone.net/router/utstar300r2unew.html

John09 · 09-20-09, 09:12 AM

All I am seeing in vonge device is error msg 008 which means user id/ pw is not correct. But I am using same user/pw in airtel modem during pppoe mode and I check with airtel rep too.

My question is why airtel modem showing both pppoe and bridge mode are enable.

Thanks.

John09 · 09-21-09, 01:34 AM

I have followed your instructions and I am seeing error 008 in vonage device. The vonage error message for this error# is invalid username/password. But the airtel gave a bit user id like <phonenumber>_ap@airtel.xxx.

Is there any one have user guild for this mode

essbebe · 09-21-09, 09:28 PM

Vonage site Userid is router
Vonage site Password is router
Website default IP is 192.168.15.1
Also try 192.168.15.1/index.html

Post Ipconfig /all data
confirm you have Vonage U.S.Number.
Beetel modem " "Always On" mode.
Delete dialer if seen in Network.

superprash2003 · 09-21-09, 09:30 PM

which vonage adapter do you have?

John09 · 09-22-09, 09:22 PM

I have reset the vonage (v-portal) and it has started working. Thanks to all of you guys with your prompt valuable responses. Again thanks for your support.

09-19-09, 11:00 PM	#1
John09 Junior Member Join Date: Sep 2009 Posts: 5 Rep Power: 0	Beetel 220 + vonage adapor I am trying to configure my vonage phone adopter using following information from this link I have followed all instructions but still my vonage device unable to connect to beetel modem. I tried to find out beetel modem user guide and I could not find one. Is any one have soft copy of user manual. Here is my WAN configuration in beeltel modem. Wide Area Network (WAN) Setup Choose Add, Edit, or Remove to configure WAN interfaces. Choose Save/Reboot to apply the changes and reboot the system. VPI/VCI Service Protocol State Status IP Address Remove Edit 1/32 pppoe_1_32 PPPoE Enabled Up 122.169.220.123 Your browser may not support display of this image. 0/35 br_0_35 Bridge Enabled Up Your browser may not support display of this image.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Need help setting up Vonage w/ Airtel Beetel 110bx1 ADSL2 + Router	vpshobha	Airtel Broadband	3	10-01-09 08:26 PM
Vonage Error [Code 004] - Help	neer001	Voice over IP	2	08-29-09 12:51 PM
Vonage problem	sphere	BSNL broadband	9	04-02-09 11:57 PM
vonage	guhanraman	Reliance Broadband	0	03-01-08 12:47 PM
reliance broadband and vonage	strogg	Reliance Broadband	7	01-22-08 02:55 AM

09-20-09, 01:37 AM	#2
essbebe Platinum Member Join Date: Aug 2007 Location: Chennai Posts: 4,240 Rep Power: 12	....enter your USERID and PW in the wan page. Enable DHCP. Connect computer using only beetel 220BX. After confirming all ok , then transfer the RJ45 from computer end to to Vonage ( Blue cable with only 4 connections ) Check the error messages and give feedback. All the 3 icons should show. Telephone/Monitor Globe. Presume you have a U.S allotted number. vonage IP 192.168.15. UserID: router PW: router. Check this link for identical modem pages. h t t p ://mydataone.net/router/utstar300r2unew.html

09-20-09, 09:12 AM	#3
John09 Junior Member Join Date: Sep 2009 Posts: 5 Rep Power: 0	All I am seeing in vonge device is error msg 008 which means user id/ pw is not correct. But I am using same user/pw in airtel modem during pppoe mode and I check with airtel rep too. My question is why airtel modem showing both pppoe and bridge mode are enable. Thanks.

09-21-09, 01:34 AM	#4
John09 Junior Member Join Date: Sep 2009 Posts: 5 Rep Power: 0	I have followed your instructions and I am seeing error 008 in vonage device. The vonage error message for this error# is invalid username/password. But the airtel gave a bit user id like <phonenumber>_ap@airtel.xxx. Is there any one have user guild for this mode

09-21-09, 09:28 PM	#5
essbebe Platinum Member Join Date: Aug 2007 Location: Chennai Posts: 4,240 Rep Power: 12	Vonage site Userid is router Vonage site Password is router Website default IP is 192.168.15.1 Also try 192.168.15.1/index.html Post Ipconfig /all data confirm you have Vonage U.S.Number. Beetel modem " "Always On" mode. Delete dialer if seen in Network.

09-21-09, 09:30 PM	#6
superprash2003 Platinum Member Join Date: Feb 2008 Posts: 2,692 Rep Power: 5	which vonage adapter do you have?

09-22-09, 09:22 PM	#7
John09 Junior Member Join Date: Sep 2009 Posts: 5 Rep Power: 0	I have reset the vonage (v-portal) and it has started working. Thanks to all of you guys with your prompt valuable responses. Again thanks for your support.

India Broadband Forum

Beetel 220 + vonage adapor

Beetel 220 + vonage adapor

Similar Threads