Thread: Airtel BB Max 150 GB plan need to connect MP 202 VOIP (ATA) Device with static IP

Hi
we have (BB MAX 150 plan) Binatone Router/modem/wifi and 2 additional public IP from Airtel everything is ok but now we need to connect Voip device MP 202 with addtional public IP so I hope following diagram will true for this ,

1) Switch -> Binatone wifirouter modem (on port2) / MP 202 (Novanet) VOIP device (on port 3)

or

2) Binatone wifirouter modem -> (on lan port) MP 202 (Novanet) VOIP device (on port 3) with static(Public IP).

or

3)Binatone wifirouter modem -> (on lan port) MP 202 (Novanet) VOIP device (on port 3) with DHCP IP.

kindly help.....

For VOIP an Internet connection is required.
Presume Binatone modem+wifi router is connected.

Now you have Lan1 LaN2 Lan3 Lan4
May be Binatone specifies Lan2 to connect VOIP unit.==>phone/s
and Lan3 FOR IPTV
( checking up )

You can connect a switch to LAN1 or Lan 4 for additional computers. Also wifi mode for laptops. within range. ( say radius of 30 feet )

CONFIRM.
with Binatone model number and Firmware version.

My setup: BSNL ISP==>>Beetel 110TCI==>OOMA or Vonage==Modem Port>>Phoneoutlet two. .
OOMA Home Port to computer. ( when needed )

Thanks a lot for your reply. But can I configure my VOIP device with Airtel Additional Public IP and connect it on Binatone Lan port.

Thanks again

YES.
probably you want to keep one STATIC IP connection exclusively
for VOIP trafffic.

AirtelISP Phone Jn==>>aDSL SPLITTER==>>mODEM PORT==rJ11 TO bINATONE
( There is special setting for VOIP /stb(IPTV) IN SOME MODELS) )
LAN4 TO LAPTOP OR DESKTOP lan ethernet connection
( to check Internet is working else not needed )
LAN1TO voip UNIT===>> PHONE/s.
Laptops will work in wifi mode.
( some models LAN2 LAN3 reserved for IPTV/VOIP , check out if any problem.)
.

As per Airtel support guy said we need to set Natting on Binatone Router modem. But now I cant access my Binatone router modem (which is configured using static Public IP) from internet.

Are you sure you cannot access modem menu pages.

Elsewhere you have asked for Porforwarding instructions.

clarify.

Usually modem address is 192.168.1.1 Id admin Pw password.

try this:
Start RUN type cmd Ok
new window
type ipconfig /all
the gatewayIP ( modem ) is shown.

Feedback.

As per Airtel L2 support we need to open port 5060 for voip so can you send me escalation for the same on HYD NOC

Your post not understood. I am not employed by Airtel.
Send email to 121 @ airtel.in
Novanet manual: does it mention port 5060 ?
Check portforward.com for WA3002_g1 for instructions.

But now I cant access my Binatone router modem
see my signature link 192.168.1.1

Try with an additional Binatone ADSl modem ( cost less than Rs 1000/= or wifi model Rs 2000 approx )

The Internet connection is made with ADSL modem In PPPoE mode UserID/PW entered in modem wan page and DHCP enabled ), with a computer,
Remove the RJ45 to cable from computer end and connect to VOIP unit.
From a switch also will work.

As yourVOIP unit is for commercial use, could not get details from the company Novanet. ( received reply for my email to them )

It has been done I have created NATTING on device and Airtel was block 5060 port so we send request email to Airtel 121 and now all is well