Thread: how to configure BSNL Type IV (MT841) modem for autodail and wireless setup.

New Page 1
h t t p://210.212.160.18/broadband-conf/type4.htm

New Page 1

VPI VCI 0 and 32 for MTNL rest as usual.

I made the changes as follows :-

PVC-0 0 / 32 PPPoE

PVC-1 8 / 35 Bridged

PVC-2 0 / 100 Bridged

PVC-3 0 / 35 Bridged

PVC-4 8 / 81 Bridged

PVC-5 8 / 32 Bridged

PVC-6 14 / 24 Bridged

Previously, the 0/32 combination was at PVC-3 and PVC-0 was 0/35. I changed PVC-0 to 0/32 and PVC-3 to 0/35 as shown above. Now the modem is being connected. But it is automatically reconnectin after 60 seconds i.e the link goes off and again reconnects automatically.

What could be the possible solution for this..????

congrats.
please check whether any entry for Idle time it should be 0 ( zero)
Also any option for "Always On " check that also.
Please see the screen shots again.
Update:
In DHCP POOL Please enter max time say 1440 minutes.
save and reboot.

hey thanks for ur help and such a quick response.... I am really impressed

i changed the settings in DHCP.. Previously it was 720 and now I changed it to 1440... however i didnt find other two options....

Now lets hope for the best..!!!

Hey dude..... it worked man.... the connection is now stable.... Thanks a lot for the help..... by the way... wat exactly does this time indicate..???

Thanks a lot dude.... it worked man.... thanx once again...!!!!

I have BSNL Type IV modem. It works fine as long as I give the IP as 192.168.1.10 When I change the setting to "Obtain an IP address automatially" and "Obtaiin DNS address automatically" it is not connecting to internet. Can some one let me know how to configure the modem so that I use the option "Obtain an IP address automatically"? Thanks!

ensure DHCP is enabled in modem http://prash-babu.blogspot.com/2008/...-modem-or.html

If MT841 this user manual may be useful.

http://www.bangaloretelecom.com/dataone/MT841.doc

thanks

hi this is arnab, have a BSNL Type IV (MT841) modem and few days ago i configured my modem as here written, it works properly. but 1 day ago when i am doing my personal work on net, suddenly it disconnected automatically. i thought it was a net problem, but i try LAN connection, it worked, then i reset my modem and try again with the written setup. but it wont connect. although some time it connects but no pages cant load from internet. it says try again. please help me. what should i do.:48::48:

then i reset my modem and try again with the written setup.

1.confirm POST No 1 in this thread.
2. TRY
New Page 1
h t t p://210.212.160.18/broadband-conf/type4.htm
http://www.bangaloretelecom.com/dataone/MT841.doc
http://www.calcuttatelephones.com/da...all/mdm07.html
3.
Mention whether you need wireless mode also ?
4.
Do you have the Wireless card to be inserted in the modem MT841 ?

FEEDBACK +ve or -ve.

I have a old Huwei MT841 with a wireless card which works perfect with autodial on BSNL broadband using steps above.
Now I need to configure it similarly for MTNL Mumbai since I have shifted my residense. Can someone help?

For mtnl VPI/VCI is 0 and 32.
UserID and PW if entered in modem to be changed.
DNS use open dns 208.67.220.220 and 208.67.222.222
or provided by MTNL.
[SKIP]
You need not disturb/delete BSNL settings.
If you still have BSNL BB connection same modem
is connected to concerned ISP's phone line. .
[/SKIP]

I can connect to net with wireless when my modem is in always on i.e. autodial.
i cant get connected with maual dial (wireless).
my laptop is showing that mt841 network connected. But when i dial through connecting box , it shows connecting through wan(pppoe) and shows error 678.

Please Help.

I have BSNL MT841 modem and hve set it on autodail as per the instructions, but still i am not being able to connect to the internet. It is showing DNS problems. I have filled in the values for DNS, but still problem presists. How can I solve it.

essbebe, what if we are using BSNL BB>> DO i have to change the values as per MTNL??

are you able to open http://192.168.1.1 ??are you able to open http://209.85.171.100

@aanup.
Not clear whether you are using MTNL or BSNL.
If BSNL in WAN settings select VPI/VCI 0 and 35
If MTNL 0 and 32. These are critical settings.
Change only theRJ11 to modem from concerned Phone line.
Rest of the settings common for both in "Bridged" mode.

Use an external dialer to test.
Then change settings in WAN page for always on
.Enter UserId without @ bsnl.in and password.

Check connection with LANport of modem/ethernet port connection. of desktop and laptop .
Then WIFI in unsecured mode. If Ok
enter security WPA key.

Add to book marks this link ( from GOA BSNL) for reference .
You cannot find a better link than this , showing settings with screen shots..

New Page 1
h t t p://210.212.160.18/broadband-conf/type4.htm

Originally Posted by India Broadband Internet

This is the step by step prodcedure on how to configure BSNL Type IV (MT841) modem for autodail and wireless setup.

First do not insert the WLAN card in to your modm. connect it with supplied LAN cabel or via usb.

Go to your computer eathernet connection setup and change the ip of your eathernet card to the following.

IP Address : 192.168.1.2
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1

now in you browser windows open up the configuration screen of mt 841
in the left side you see the wizard from basic drop down list select connections. Left side you see PVC0 to PVC6 now you only need to change the value of PVC0 to dial up the connection automatically with PPPoE setup. but some how you can not edit the connection of PVC0 by clicking the note icon on the configuration screen. it only let you change the settings for wich the PVC is created and let you delete it. so you need to delete all the PVC in the list. Stat from PVC6 press notes icon and delete.

Do the same process for PVC6 to PVC2 and PVC0 do not delete PVC1 untill you create new PVC.

now press the new button and create new PVC specify following parametere in the PVC

WAN Type : PPPoE
VPI/VCI : 0/35
Encapsulation : LLC
Default Route : Enable
User Name : <Your User Name>
Password : <your password >
use DNS : Ebable

now click on apply. It will show new PVC and it display it as PVC1 now delete PVC0 from the list and start create remaining PVC for your connection by pressing new.

All PVC shoud have following property.

Wan Type : Bridge
Encapsulatino : LLC

and for VPI/VCI follo this steps

PVC1 : 8 /35
PVC2 : 0 /100
PVC3 : 0 /32
PVC4 : 8 /81
PVC5 : 8 / 32
PVC6 : 14 / 24

now you have created all the PVC's with you dialer configured at PVC1

go to advanced select Firewall and select enable.
go to DNS selct Ebable and put following value in the dns

Primary DNS : 61.1.96.69
Secondry DNS : 61.1.96.71

save your change and reboot the router.

after reboot you should be automatically connect to the internet without dialing PPPoE dialer from the computer. now turn off the router and connect the WLAN Card to the router and disconnect the lan cabel from the modem and computer. after you see the WLAN light on in the router stat your wifi connection from compuer or modem to search for availabe network and you will be connected to the net. for any help you can contat me.

hi there,according to the suggestion, i have deleted pvc and created a new pvc with 0/35 after saving,my modem is not able to connect with internet and the green light of LINK in modem turns ORANGE now,and now I am unable to connect 192.168.1.1 even.
what i did ,I used another modem from which I am able to connect with internet but my 841AX modem is not working what should I do now ?

hi there,according to the suggestion, i have deleted pvc and created a new pvc with 0/35 after saving,my modem is not able to connect with internet and the green light of LINK in modem turns ORANGE now,and now I am unable to connect 192.168.1.1 even.
what i did ,I used another modem from which I am able to connect with internet but my 841AX modem is not working what should I do now ?

@maahisingh.

[PROBLEM

....but my 841AX modem is not working what should I do now ?

Reset the modem to factory settings ,
With power on to modem press the switch( in the rear)
for about 30 to 40 seconds.
Now see any of these links and follow instructions.

SmartAX MT-841 (Type-III) ADSL MODEM MULTIUSER CONFIGURATION


CONFIGURATION

SmartAX MT-841 (Type-IV) ADSL MODEM MULTIUSER CONFIGURATION

[

Hi can you forward that tutorial to me too.

Hi can you forward that tutorial to me too

Please click the links given earlier for the official websites.
or give details of your problem.
OS used ; windows Xp linux etc
Modem ' mt841 etc
Connection :" "Dialer" ( "bridged") mode :use window in computer or
"Always On" PPP/PPPoE ( UserId/PW entered in Modem WAN page)

Feedback.

http://www.calcuttatelephones.com/da...tall/mu06.html