India Broadband Forum

essbebe · 03-17-09, 09:36 PM

Please refer to numbers given by me
and post the results.

Give enough space between sentences.

For 1: username without @ dataone.in or @bsnl.in
YES NO

For 2: did you see the "NOTE" icon ? and click it ?
YES NO

For 3: Not tried .
For 4: not tried
For 5: could not proceed further.

Para two:
I have the same modem MT882, and
I have to do it in PPP/PPPoE
mode everytime I switch on the modem.
and when I select different ISPs settings.

govind236 · 03-18-09, 09:21 AM

1. Did as instructed.
Yes username entered without @dataone.in or @bsnl.in

2. Yes. Note icon appeared and i clicked on it to connect

3. I did not get connected to the internet so Not tried

4. Not tried

5. Not tried

What numbers are you talking about?

essbebe · 03-18-09, 09:53 AM

@govind236
Problem : AXmT882

Quote:

I get green status in the modem configuration page for WAN and LAN but in the modem the Link LED is red and I get error 678 if I try to dial and connect to the internet.

Please refer this link for "always on" connection.
http://www.calcuttatelephones.com/da...tall/mu03.html

If still not getting connected

Post following data.
Start/ RUN type cmd type ipconfig /all

Para two: To connect linksy's WRT54G . will wait for
feedback for above.

govind236 · 03-18-09, 09:58 AM

(A) yes i am getting connected to internet.

none of my settings have changed from the original settings that i was using since 2 years.

my WAN type is RFC2684Bridged. If i change it to PPP internet stops working

(B) I use a dialer to connect.

Thank you for your patience.

essbebe · 03-18-09, 10:19 AM

UPDATE:0928am: No changes required in modem. MT882.
Advise save the settings to your harddisk.
=======================
Fine.
If you are satisified there is no problem.
are you interested in connection the LINKSY WIFI unit ?
Please check the Forum "Broadband How to.... " for a
similar setup to connect a wireless router.

or see this link.
http://socrates0.blogspot.com/2007/1...ys-wrt54g.html

I don't have this router and would prefer ,
if you can refer screen shots in this blog for reference,
if there is a problem.

govind236 · 03-18-09, 10:25 AM

Hi thanks so much for your help

1. My WAN setting is now PPP/PPPoE.

2. Have entered username and password in modem settings and made the connection Always On

3. Have enabled DHCP with range 192.168.1.2 to 192.168.1.33

4. Changed IP properties from Network->Lan->Properties to "Obtain automatically"

5. Clicked on the Note Icon and now I am connected to Internet and can surf normally

6. Do I have to change any other settings in my modem or I can now proceed to configuring the Linksys router???

sanmalkani · 03-18-09, 03:59 PM

Quote:

Originally Posted by samking

Main Question:
I have the Huawei modem (Type II) wireless Ethernet and USB that BSNL gives. I want to use this with Airtel, is that possible? If yes, how?

History: (if interested)
I am switching from BSNL to Airtel becasue BSNL has not shifted my connection to my new house since the last 4 months.
I was extremely satsfied with the 512MB/5GB deal. Then I shifted my house and applied to BSNL for shifting my connection. It's been so long. it's crazy! I spent approx Rs.5500 to get the damn thing (deposits, installation, modem purchase, etc.). Now they are giving me some stupid excuses and not shifting the connection to the new place.

Airtel came 3 months ago and dug up the road one day, laid the cable and put the box the next day. Then they came door-to-door offering the connections for just 500 bucks! (refundable!) and 700 bucks a month rental!
I dint take it then in the hopes of getting BSNL, but they have let me down.

Now I want to take the Airtel thing, but I have this 1800 rupee modem that I got from BSNL, I don't want to spend on another Airtel modem.
The Airtel technicians will not help me since they want to sell their own modem.

Please help me find a way to use the hawa-hawai modem with hawa-tel!

well it is your choice for selecting the operator but i would suggest that u should conatact the BSNL JTO/SDO (area incharge) even now a days u can contact to GM.they will definitely help u.actually private operators offers seem to be lucarative but all are withh hidden cost.

essbebe · 03-18-09, 06:27 PM

@sanmalkani
Please quote the POST No in this thread.
of message posted by @samking.
Difficult to scroll through all the pages. ( 160 messages)

He has to change the VPI/VCI to 1 and 32 in the
bsnl modem he has, for Airtel usage.
Use Airtel provided DNS or
opendns 208.67.220.220
and 208.67.222.222
Rest as usual.

Quote:

......
Now I want to take the Airtel thing, but I have this 1800 rupee modem that I got from BSNL, I don't want to spend on another Airtel modem.
The Airtel technicians will not help me since they want ......

Whether he wants or not AIRTEL will supply a modem
FREE of RENT. A Non refundable security deposit will be taken. Neither He can buy the modem nor Airtel will sell one !

Poor GM BSNL already getting grey hairs.!
( Rather he becomes GM after getting grey hairs!)
Leave him alone for these minor matters !!!

soumya1985cool · 03-26-09, 07:05 PM

hello, i just got an n81 and was trying to connect to the wlan. My laptop gets connected via wlan but my cell phone doesn. though every time i refresh it gets connected to the network but when i start browsing i get "No gateway reply".My cell is working fine because i got connected via bsnl broadband (dont know who's as he dint had any security setting enabled

). so i thincertain setting is required.
my setting include wep key and when connected to wireless i require to put the bsnl's provided username and password.
my modem is siemens sl2_141

thanks
soumya

vitthal1 · 03-28-09, 05:00 AM

Hi,
Thanks for your detailed post.
I am using BSNL trype 2 modem. I also tried to use wireless connection, but couldnt. whenever i use wireless without WEP encryption, it works and the moment i tried to put password, it disconncted. can u help me to know how to fix this problem.

I am using UTStsarcom (WA3002G4) modem.

Thanks
Vitthal

essbebe · 03-28-09, 08:40 AM

Quote:

I am using UTStsarcom (WA3002G4) modem.

see this link which includes screen shots.
h t t p://mydataone.net/router/wa3002g4.html

Quote:

my modem is siemens sl2_141

( similar to Sl2_141 also )
Try "Always On" mode instead of dialer mode.

Feed back.

rijeesh · 03-31-09, 03:22 PM

I can acces internet from both laptop and pc(one is wired and other through wirless) how to setup networking with laptop and pc through wifi(Utstarcom-Bsnl)

srijand · 04-03-09, 10:02 PM

Hi,
I have a bsnl dataone broadband connection with the Huawei SmartAX MT882 dsl modem.

I am about to purchase a Netgear WGR614 wireless router to create a wireless network in my home. I need some help with the following queries:

1. Are there any speed / compatibility issues between the SmartAX MT882 and Netgear WGR614? Do they work properly together or should I go for another router?

2. Which is better - a USB network adapter or a PCI network adapter?

3. Is it possible for me to access my broadband internet connection wirelessly with the host computer turned off? What I mean is, if the main computer to which my MT882 modem is connected is turned off, and only the modem and wireless router are switched on, can I still access my internet connection wirelessly using my other computer (which has a wireless adapter)?

Thank you!
-Srijan

essbebe · 04-04-09, 12:48 AM

.1 With speed upto 2 Mbps only available for Home users mostly
no issues with MT882+WGR614.
2.PCI network adapter /Ethernet card
3. YES. computer Desktop or Laptop on WIFI mode will work
Modem==>>> wifi router== Laptop
Modem====wifirouter===LAN1 == desktop
Modem==USBport === desktop.

srijand · 04-27-09, 09:27 PM

I have a Huawei SmartAX MT882 adsl modem and I recently bought a netgear WGR614 wireless router. I've been trying hard, unsuccessfully, to configure it.

I followed the instructions here and changed the WAN settings accordingly. After the modem restarted, the Status on the Summary page was Red, as expected.

But after clicking on the plug icon in the notes column, it still doesn't connect and it stays red. Now I don't know what to do.

Also, after changing the WAN settings, I can no longer connect to the internet. I have to reset the modem to factory defaults in order to connect.

Please help!
Thanks.

essbebe · 04-28-09, 11:10 AM

Step 1 ;Connect only MT 882 LAn port to computer.
Step 2:
Start /network/ LAn properties
TCP/IP ( *click)
Properties(*click)

enter
Ip address 192.168.1.10
subnet 255.255.255.0
defualt 192.168.1.1
Dns '
opendns
208.67.220.220
208.67.222.222
Apply save.

Step 3. Now enter 192.168.1.1 in IE address bar
If you get the modem settings open
select PPP/PPPoE ( not bridged0 in Wan page.
Enter user Id ( without @ bsnl.in) PW
etc. SAVE REBOOT wait for 2 minutes.

After the modem restarts go to Summary page
click the "NOTE" icon 0_35 connection will be green.
wait
confirm you are connected to Internet
more later=====>>>>
:

srijand · 04-28-09, 02:43 PM

Hi,

Thanks for your reply.
I tried changing the settings according to your instructions, but it still doesn't work. The "NOTE" icon 0_35 connection doesn't turn green after clicking it, it stays red and I cannot connect to the internet.

Also, I couldn't connect to the internet in the conventional manner (using network connections) until i reset the modem and changed my tcp/ip settings back to 192.168.1.2 (from 192.168.1.10).

Please help!
Thanks!

essbebe · 04-28-09, 05:09 PM

@srijand

Quote:

I have to reset the modem to factory defaults in order to connect.

How you connect Dialer" mode or "Always On '
in this condition post ipconfig /all data.

or in DNS enter 192.168.1.1 and 208.67.220.220 and try.

Quote:

the "NOTE" icon 0_35 connection doesn't turn green

in line 0_35 after all entries Green button will appear. next to that "NOTE' icon
when you click it
the connection will be made.
refer
http://www.calcuttatelephones.com/da...all/mdm03.html

In all posts present position brief summary to be shown.
members , just reading the latest post tend to reply only to that fault. ( who will read 177 posts, find out your original post and then follow up all the replies and then post their comments ?
Para two :
out of thread:

A cryptic post like I tried "it" . But "that"
did not work. And my modem is supplied by the ISP.
Or i got it from America.
should I try " "something" else,
I formatted the hard disk , etc will not elicit any response !!!

srijand · 04-28-09, 06:19 PM

I configured my modem according to the settings on calcuttatelephones .com and this seems to have worked. Now the the "NOTE" icon 0_35 connection has turned green. I am in 'always on' mode. Should I now proceed to configure the rest of the settings as mentioned in the very first post of this thread?

ipconfig data:

Code:

Windows IP Configuration

Host Name . . . . . . . . . . . . : srijan-net
Primary Dns Suffix  . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No


Ethernet adapter Local Area Connection 2:

Connection-specific DNS Suffix  . :
Description . . . . . . . . . . . : Silan SC92031 PCI Fast Ethernet Adapter
Physical Address. . . . . . . . . : 00-E0-20-AC-BC-A9
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.1.10
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : 61.0.0.5
                                    61.1.96.69
                                    61.1.96.71

History:
I have a Huawei SmartAX MT882 adsl modem and I recently bought a netgear WGR614 wireless router. I've been trying hard, unsuccessfully, to configure it.

I followed the instructions here and changed the WAN settings accordingly. After the modem restarted, the Status on the Summary page was Red, as expected.

But after clicking on the plug icon in the notes column, it still doesn't connect and it stays red. Now I don't know what to do.

Also, after changing the WAN settings, I can no longer connect to the internet. I have to reset the modem to factory defaults in order to connect.

essbebe · 04-28-09, 08:05 PM

@srijand

Quote:

settings on calcuttatelephones .com and this seems to have worked.

OK.
summary : start POST no 173.
MT882 set to connect to Internet on "Always on" mode.
Now trying to connect wgr614.
see this : my set up.

Quote:

MT882 airtel
PVC4 1 / 32 122.164.51.x 122.164.xx.xx 255.0.0.0 PPPoE green "note"icon

in TCp/Ip obtain Ip address automatically . DNS you can enter your choice BSNL or Opendns .
First try the LAN mode.
then WIFI.

Quote:

C:\Documents and Settings\essbebe.STARNOTE>ipconfig /all

Windows IP Configuration
Host Name . . . . . . . . . . . . : starnote
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Wireless Network Connection 2:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Wireless Notebook Adapter MN-720 #2
Physical Address. . . . . . . . . : 00-xD-3A-6z-A0-xx (*corrupted)
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 192.168.2.2
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.2.1
DHCP Server . . . . . . . . . . . : 192.168.2.1
DNS Servers . . . . . . . . . . . : 192.168.2.1
Lease Obtained. . . . . . . . . . : Tuesday, April 28, 2009 6

03 PM
Lease Expires . . . . . . . . . . : Wednesday, April 29, 2009 6

03 PM

03-17-09, 09:36 PM	#161
essbebe Platinum Member Join Date: Aug 2007 Location: Chennai Posts: 4,246 Rep Power: 12	Please refer to numbers given by me and post the results. Give enough space between sentences. For 1: username without @ dataone.in or @bsnl.in YES NO For 2: did you see the "NOTE" icon ? and click it ? YES NO For 3: Not tried . For 4: not tried For 5: could not proceed further. Para two: I have the same modem MT882, and I have to do it in PPP/PPPoE mode everytime I switch on the modem. and when I select different ISPs settings. Last edited by essbebe; 03-17-09 at 09:52 PM.

03-26-09, 07:05 PM	#169
soumya1985cool Junior Member Join Date: Mar 2009 Age: 24 Posts: 1 Rep Power: 0	well i want to connect my phone.. hello, i just got an n81 and was trying to connect to the wlan. My laptop gets connected via wlan but my cell phone doesn. though every time i refresh it gets connected to the network but when i start browsing i get "No gateway reply".My cell is working fine because i got connected via bsnl broadband (dont know who's as he dint had any security setting enabled ). so i thincertain setting is required. my setting include wep key and when connected to wireless i require to put the bsnl's provided username and password. my modem is siemens sl2_141 thanks soumya Last edited by soumya1985cool; 03-26-09 at 07:09 PM. Reason: forgot to mention my modem..

03-28-09, 05:00 AM	#170
vitthal1 Junior Member Join Date: Mar 2009 Age: 28 Posts: 1 Rep Power: 0	vitthal Hi, Thanks for your detailed post. I am using BSNL trype 2 modem. I also tried to use wireless connection, but couldnt. whenever i use wireless without WEP encryption, it works and the moment i tried to put password, it disconncted. can u help me to know how to fix this problem. I am using UTStsarcom (WA3002G4) modem. Thanks Vitthal

03-31-09, 03:22 PM	#172
rijeesh Junior Member Join Date: Mar 2009 Location: Palakkad, Kerala Posts: 1 Rep Power: 0	How to acces files of pc from laptop through wirless by bsnl wifi modem I can acces internet from both laptop and pc(one is wired and other through wirless) how to setup networking with laptop and pc through wifi(Utstarcom-Bsnl)

04-03-09, 10:02 PM	#173
srijand Junior Member Join Date: Nov 2008 Age: 25 Posts: 10 Rep Power: 1	Netgear WGR614 queries - Help please! Hi, I have a bsnl dataone broadband connection with the Huawei SmartAX MT882 dsl modem. I am about to purchase a Netgear WGR614 wireless router to create a wireless network in my home. I need some help with the following queries: 1. Are there any speed / compatibility issues between the SmartAX MT882 and Netgear WGR614? Do they work properly together or should I go for another router? 2. Which is better - a USB network adapter or a PCI network adapter? 3. Is it possible for me to access my broadband internet connection wirelessly with the host computer turned off? What I mean is, if the main computer to which my MT882 modem is connected is turned off, and only the modem and wireless router are switched on, can I still access my internet connection wirelessly using my other computer (which has a wireless adapter)? Thank you! -Srijan

India Broadband Forum

Making the BSNL DataOne Wireless home network guide

Making the BSNL DataOne Wireless home network guide

Similar Threads

03-18-09, 09:21 AM	#162
govind236 Junior Member Join Date: Mar 2009 Posts: 7 Rep Power: 1	1. Did as instructed. Yes username entered without @dataone.in or @bsnl.in 2. Yes. Note icon appeared and i clicked on it to connect 3. I did not get connected to the internet so Not tried 4. Not tried 5. Not tried What numbers are you talking about?

03-18-09, 09:58 AM	#164
govind236 Junior Member Join Date: Mar 2009 Posts: 7 Rep Power: 1	(A) yes i am getting connected to internet. none of my settings have changed from the original settings that i was using since 2 years. my WAN type is RFC2684Bridged. If i change it to PPP internet stops working (B) I use a dialer to connect. Thank you for your patience.

03-18-09, 10:19 AM	#165
essbebe Platinum Member Join Date: Aug 2007 Location: Chennai Posts: 4,246 Rep Power: 12	UPDATE:0928am: No changes required in modem. MT882. Advise save the settings to your harddisk. ======================= Fine. If you are satisified there is no problem. are you interested in connection the LINKSY WIFI unit ? Please check the Forum "Broadband How to.... " for a similar setup to connect a wireless router. or see this link. http://socrates0.blogspot.com/2007/1...ys-wrt54g.html I don't have this router and would prefer , if you can refer screen shots in this blog for reference, if there is a problem.

03-18-09, 10:25 AM	#166
govind236 Junior Member Join Date: Mar 2009 Posts: 7 Rep Power: 1	Hi thanks so much for your help 1. My WAN setting is now PPP/PPPoE. 2. Have entered username and password in modem settings and made the connection Always On 3. Have enabled DHCP with range 192.168.1.2 to 192.168.1.33 4. Changed IP properties from Network->Lan->Properties to "Obtain automatically" 5. Clicked on the Note Icon and now I am connected to Internet and can surf normally 6. Do I have to change any other settings in my modem or I can now proceed to configuring the Linksys router???

04-04-09, 12:48 AM	#174
essbebe Platinum Member Join Date: Aug 2007 Location: Chennai Posts: 4,246 Rep Power: 12	.1 With speed upto 2 Mbps only available for Home users mostly no issues with MT882+WGR614. 2.PCI network adapter /Ethernet card 3. YES. computer Desktop or Laptop on WIFI mode will work Modem==>>> wifi router== Laptop Modem====wifirouter===LAN1 == desktop Modem==USBport === desktop.

04-27-09, 09:27 PM	#175
srijand Junior Member Join Date: Nov 2008 Age: 25 Posts: 10 Rep Power: 1	Problem configuring SmartAX MT882 - HELP! I have a Huawei SmartAX MT882 adsl modem and I recently bought a netgear WGR614 wireless router. I've been trying hard, unsuccessfully, to configure it. I followed the instructions here and changed the WAN settings accordingly. After the modem restarted, the Status on the Summary page was Red, as expected. But after clicking on the plug icon in the notes column, it still doesn't connect and it stays red. Now I don't know what to do. Also, after changing the WAN settings, I can no longer connect to the internet. I have to reset the modem to factory defaults in order to connect. Please help! Thanks.

04-28-09, 11:10 AM	#176
essbebe Platinum Member Join Date: Aug 2007 Location: Chennai Posts: 4,246 Rep Power: 12	modem SmartAx Mt 882 settings. Step 1 ;Connect only MT 882 LAn port to computer. Step 2: Start /network/ LAn properties TCP/IP ( click) Properties(click) enter Ip address 192.168.1.10 subnet 255.255.255.0 defualt 192.168.1.1 Dns ' opendns 208.67.220.220 208.67.222.222 Apply save. Step 3. Now enter 192.168.1.1 in IE address bar If you get the modem settings open select PPP/PPPoE ( not bridged0 in Wan page. Enter user Id ( without @ bsnl.in) PW etc. SAVE REBOOT wait for 2 minutes. After the modem restarts go to Summary page click the "NOTE" icon 0_35 connection will be green. wait confirm you are connected to Internet more later=====>>>> :

04-28-09, 02:43 PM	#177
srijand Junior Member Join Date: Nov 2008 Age: 25 Posts: 10 Rep Power: 1	Hi, Thanks for your reply. I tried changing the settings according to your instructions, but it still doesn't work. The "NOTE" icon 0_35 connection doesn't turn green after clicking it, it stays red and I cannot connect to the internet. Also, I couldn't connect to the internet in the conventional manner (using network connections) until i reset the modem and changed my tcp/ip settings back to 192.168.1.2 (from 192.168.1.10). Please help! Thanks!

04-28-09, 06:19 PM	#179
srijand Junior Member Join Date: Nov 2008 Age: 25 Posts: 10 Rep Power: 1	I configured my modem according to the settings on calcuttatelephones .com and this seems to have worked. Now the the "NOTE" icon 0_35 connection has turned green. I am in 'always on' mode. Should I now proceed to configure the rest of the settings as mentioned in the very first post of this thread? ipconfig data: Code: Windows IP Configuration Host Name . . . . . . . . . . . . : srijan-net Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Silan SC92031 PCI Fast Ethernet Adapter Physical Address. . . . . . . . . : 00-E0-20-AC-BC-A9 Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.1.10 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 61.0.0.5 61.1.96.69 61.1.96.71 History: I have a Huawei SmartAX MT882 adsl modem and I recently bought a netgear WGR614 wireless router. I've been trying hard, unsuccessfully, to configure it. I followed the instructions here and changed the WAN settings accordingly. After the modem restarted, the Status on the Summary page was Red, as expected. But after clicking on the plug icon in the notes column, it still doesn't connect and it stays red. Now I don't know what to do. Also, after changing the WAN settings, I can no longer connect to the internet. I have to reset the modem to factory defaults in order to connect.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
BSNL DataOne truly rocks!	India Broadband	BSNL broadband	2	09-04-09 10:55 PM
BSNL Dataone Home500 No charge till 5GB+40p/MB	India Broadband	Sify broadband	2	07-05-09 10:24 AM
Dataone rocks, BSNL Sucks!	India Broadband	BSNL broadband	2	10-29-08 02:06 AM
Top 5 reasons to switch to BSNL DataOne	Admin	BSNL broadband	0	04-03-06 04:29 AM
BSNL has tied up with HCL Infosystems Ltd. to launch the BSNL HCL PC for DataOne broa	Admin	BSNL broadband	0	04-03-06 04:26 AM