Thread: configuration for DLINK glb 802c

i like to know the web configuration for GLb 802 C please

1.No user manual download available in Dlink.in web site. for GLB802C
released in INDIA around August 2008.
2. See this link and check your settings ( for GLB502T) should be similar.
dlink.in/GLB502T_Guide_modified/BSNL_PPPoE.htm

http://dlink.in/GLB502T_Guide_modified/BSNL_PPPoE.htm

Para two : A request.
If

you have a CD for installation can you upload the manual/drivers etc ?
http://dlink.co.in/GLB502T_Guide_mod...BSNL_PPPoE.htm

Else
If settings are same please confirm.

Right, here's how to configure your D-Link GLB-802C . . .
This is assuming that you have already plugged in the ethernet cables into modem / Pc from Splitter etc .

Step 1 - open your web browser and navigate to your router page "192.168.1.1" enter your default username / password which is admin (username) and admin (password)

Step 2 - click on Quick Configuration, on this page enter the settings as follows
Connection Name - Bsnl
Operation Mode - Enabled
Connection Type - PPPoE LLC
VPI - 0
VCI - 35
IGMP - Disabled
IP Address - Leave it default "0.0.0.0"
Subnet Mask - Leave it default "0.0.0.0"
Use DHCP - Enable
Default Route - Enabled
Gateway IP Address - Leave it default "0.0.0.0"
Username - Enter your Username from Bsnl
Password - Enter your password from Bsnl
Use Dns - Enable

Now click on Submit, then click on Admin Tab and click on Commit and reboot
Give the modem time to reboot.
That's it !

thank you very much

No Worries

this router is troubling me for past 2 months.exactly 5 minute disconnection of DSL link :x .I need to take it for repair under gurantee.no firmware updates ,nothing for this model yet?
oh! and overheating too.

@prakash_mvpa
Please try GDMT as mod selected.

Can I connect Lan & USB at the same time?

Send big files the easy way. Files too large for email attachments? No problem!

Yes. to different computers.
You need usb driver for the modem/router.
Do you have the CD ?

yes I have installed Usb drivers but can't get PPPOE to work

1.Post ipconfig /all data
for both connections.
(a)LAN Port as well as (b)USB port.

2.a. Uninstall the USB drivers.
b.disconnect USB port cable from computer end. .
c.Insert CD and copy the drivers to say C:/802C usb drivers. Switch off computer.
d. connect USB cable again.
e.restart computer.
f. Let Windows detect new hardware.
g. When drivers are asked copy from (c)
test again the two computers.

The Lan PC is set to obtain Ip address automatically,I set the Usb PC IP as 192.168.2.10

since Usb & Lan have to be in different subnets in 802 c


Ipconfig/all from the Usb PC



Windows IP Configuration

Host Name . . . . . . . . . . . . : 2xxxxxxxxx
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Area Connection 2:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : D-Link GLB-802C ADAPTER
Physical Address. . . . . . . . . : 00-85-A0-01-01-04
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.1.10
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.2
NetBIOS over Tcpip. . . . . . . . : Disabled

PPP adapter internetz:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface
Physical Address. . . . . . . . . : 00-53-45-00-00-00
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 117.195.132.32
Subnet Mask . . . . . . . . . . . : 255.255.255.255
Default Gateway . . . . . . . . . : 117.195.132.32
DNS Servers . . . . . . . . . . . : 218.248.255.146
218.248.255.139
NetBIOS over Tcpip. . . . . . . . : Disabled


2nd step done

Just to clarify I have 2 seperate PCs.

One I'm connecting through Usb & the other through the Lan port of the router

2nd step done

1.Computer 1 on LAN port OK.
Try USB port for this computer.
Confirms drivers OK. settings ok.

2.Computer 2 on USB port Not working.
Test LAN port here.
confirms computer settings ok !.

3. I think you have to enable DHCP
and also select Obtain Ip address automatically
in Computer 2. ( when using USB port )
4. Netbios over TCP/IP usually "default" selected
( see TCP/IP properties DNS "advanced " wins etc bottom)

5. Feedback.

How do I enable DHCP? Is it enabled when Obtain Ip address automatically is selected?

Netbios over TCP/IP is at "default" setting but Ipconfig/all lists it as disabled

PPPOE doesn't seem to work over Usb

Originally Posted by muddasani1986

i like to know the web configuration for GLb 802 C please

Hi !! can you help me in configuring GLB 802C ADSL modem for MTNL broadband.

@ghost

Hi !! can you help me in configuring GLB 802C ADSL modem for MTNL broadband.

See Post No 3 in this thread.

FOR MTNL VPI/VCI 0 and 32 ( confirm )
2.
Download user manual from here.
Send big files the easy way. Files too large for email attachments? No problem!
h t t p://www.sendspace.com/file/136min