Thread: problems connecting beetel 450BX1 router to BSNL

I have a BSNL DSL connection and use a modem and LAN cable to connect to the Internet. I now want to connect my Beetel 450BX1 wireless router directly to the DSL line after the POTS splitter, and wirlessly browse the web.

I configured my Beetel wireless router for PPPoE, LLC/SNAP Bridging, VPI/VCI 0/35, UBR without PCR, AUTO authentication, MTU 1492 and enabled NAT, PPP Debug and WAN.

I set the default gateway as 192.168.1.1 (or should I change this to auto)

I also typed in my BSNL userid and password but still cannot connect to the Internet.

Here's what happens when I run diagnostics:

Test the connection to your local network
Test your ENET1 Connection: PASS
Test your ENET2 Connection: FAIL
Test your ENET3 Connection: FAIL
Test your ENET4 Connection: FAIL

Test your Wireless Connection: PASS
Test the connection to your DSL service provider
Test ADSL Synchronization: PASS
Test ATM OAM F5 segment ping:
PASS
Test ATM OAM F5 end-to-end ping:
PASS
Test the connection to your Internet service provider
Test PPP server connection: FAIL
Test authentication with ISP: PASS

Test the assigned IP address: PASS
Ping default gateway: PASS
Ping primary Domain Name Server: PASS

Please help.

Thanks!

Originally Posted by adarshk

I set the default gateway as 192.168.1.1 (or should I change this to auto)

Change it to auto, rest is fine i am using this router so ping me if you have any more problems

I tried that but still no connection. Any other ideas?? Thx.

Originally Posted by adarshk

Test the connection to your Internet service provider
Test PPP server connection: FAIL

The connection to the BSNL server is failing. Is broadband activated on your line? Are u sure that u are using the correct username/password combination? Is the link light lighting up?

Seems you have selected "Dialer" "Bridged" mode.
Option 1 :
Check your dialer
enter Userid without @ bsnl.in
Option 2: See screenshot in NO 6 Second Link ( chennai)
Go to WAN page.
Edit
Deselect "Bridged"
Enable PPP/PPPoE
Next
enter your BSNL ID without @ bsnl.in Pw
Enable PPPdebug...
Enable bridge PPPoE frames between ...... etc


enter your BSNL ID without @ bsnl.in Pw
Save reboot.
wait for two minutes.
Check connection or Diagnostics page again.

REFERENCE : this modem/ wifi router similar.
Ignore the titles and open the links.
The little I know about Dataone Broadband Services offered by BSNL
( Thanks to :@cool_techie_tvm)

Chennai Telephones- Changing password in DataOne Pre-configured modem

Thanks for the input. What I am trying to do here is replace the two boxes (modem and router) with just one Beetel 450BX1 ADSL2+ router (this doubles as a modem too - correct??)

I tried everything mentioned and finally end up with FAIL on Test PPP server connection and Test the assigned IP address.

Man - am really stumped. I tried changing my wireless connection tcpip properties to give them the gateway and dns info but no luck.

What I noticed was that my menu did not give me a choice to do:
Bridge PPPoE Frames Between WAN and Local Ports (Default Enabled)

but am guessing it's default enabled.

I can connect using BSNL's DataOne modem + Dlink router so my Broadband connection username and password are okay.

Any other ideas?? THANKS A TON, FOLKS!

Test your ENET1 Connection: PASS
Test your Wireless Connection: PASS

Test the connection to your DSL service provider
Test ADSL Synchronization: PASS
Test ATM OAM F5 segment ping: PASS
Test ATM OAM F5 end-to-end ping: PASS

Test the connection to your Internet service provider
Test PPP server connection: FAIL
Test authentication with ISP: PASS
Test the assigned IP address: FAIL
Ping default gateway: PASS
Ping primary Domain Name Server: PASS

Originally Posted by adarshk

Test the connection to your Internet service provider
Test PPP server connection: FAIL
Test authentication with ISP: PASS
Test the assigned IP address: FAIL

Have u tried resetting the router and entering the settings once again. Maybe it might work.

Bridging, VPI/VCI 0/35[.....

try PPP/PPPoE "Always On" disable "Bridged"
enter user name without @ bsnl.in and give Password.
Save reboot. Wait for two minutes.


Para two;
Post your IPconfig/all data
Confirm you get connected LAN/ethernet port.
Start/Network/Status support
See IP details.
Try Repair option. What error message you get ?

After confirming a wired connection go for WIFI.
The screen shots given in the Chennai link should be helpful.
Feedback.

I am also facing same issue, but in my "Test authentication with ISP" is in FAIL state.....

Need your help guys....


Thanks
Cute

you have not entered your UserID and Password properly.
either in the WAN page for PPPoE or In "Dialer" mode.
VPI/VCI 0 and 35 bsnl.
see this link for modem settings : with menu pages similar.
http://www.indiabroadband.net/bsnl-b...reference.html (UTSTAR WA3002-G4 quick reference).

Thanks for your prompt response, i double checked by username and password in wan page it is correct. More over i also verified the configs it is done as per the url given by you. Not sure what is wrong, this is what i see



Test authentication with ISP: FAIL
Test the assigned IP address: FAIL
Ping default gateway: FAIL

Thoughts?

Thanks
Cute

Save present settings of modem to say C:/ My Documents/modem failure
Now reset the modem factory settings.
reset access can be in the rear or near bottom right leg small round hole.
\With power on use a ballpoint pen refill to reset the micro switch for about 10 to 20 seconds.
Now use a dialer to connect .
Post this data . copy/Paste no edit.

Start run type cmd Ok
New window
type ipconfig /all

I am trying to use the same model/router with airtel. Want to use ipad wirelessly and a windows 7 based desktop with a wired connection.

replied in airtel forum.