Thread: Funny problem, worried!

Hi friends, when I try to reach the main page of the modem (192.168.1.1) the userid/pwd screen appears, once I provide the same blank screen appears. When I type 192.168.1.1/look.html the screen with some detail in chinese appear. But how to get the main page. The modem is WA3002 G4 (UTStarcom type 4). Anybody has suggestion/idea.

I am able to connect to the net in bridge mode (which is what the last time configured when this problem was not there). My OS is Mandriva 2009 and browser is Firefox.

thanks in advance.

I type 192.168.1.1/look.html
why the extra line ??

@newprouser
Sorry didn't get you

why do you type look.html

also can ya pls post a screen shot..

BTW : did you have this problem before ?

try .0 and .2

Originally Posted by newprouser

why do you type look.html

also can ya pls post a screen shot..

BTW : did you have this problem before ?

Please find the screen shots. NOTE that I never faced this problem before.

Thanks everybody, going to bed. May tomorrow be a good day!!! (as there is no further reply)

reset ur modem to factory settings from the reset button on ur modem.

@newprouser

why do you type look.html

From some other thread posted by me.
( not suggested here by me )
@matrix must have picked up this address
instead of 192.168.1.1

Para two:
After accessing modem
type 192.168.1.1/look.html
to check the FW version and corresponding
SW version.
If nothing is shown please Ignore request.

Para two:
compare with device status. ( addl info in above mode )

Originally Posted by essbebe

@newprouser

From some other thread posted by me.
( not suggested here by me )
@matrix must have picked up this address
instead of 192.168.1.1

Para two:
compare with device status. ( addl info in above mode )

Yes, it is based on your post only I typed the look.html as just 192.168.1.1 was showing only blank screen. As shown in your screen shot there is no additional info in my case. May be the modem make are different so that is the reason.... Thanks

when I try to reach the main page of the modem (192.168.1.1) the userid/pwd screen appears, once I provide the same blank screen appears.

@matrix
The problem solved ?
if not, in browser
try after entering 192.168.1.1 Id and pw
type 192.168.1.1/menu.html
the following will appear in left side.
......................... to access.
Device Info (* 192.168.1.1/info.html)
Advanced Setup (* 192.168.1.1/wancfg.cmd)
Diagnostics (* 192.168.1.1/diag.html)
Management (* 192.168.1.1/backupsettings.html)

etc etc.
Para two : 192.168.1.1/look.html
Try again. Post data. This is to check up
whether Firmware update is possible./can be tried
as last resort.

Feedback.

just check if you are using mozilla or any such browser as they have a option to block auto refresh of the page ... if you are using it then disable it and it should work fine...

@matrix

From Post 1.


My OS is Mandriva 2009 and browser is Firefox.
mention version number of Firefox.

Regarding your OS > NO IDEA about linux.

Para two:
Please enable "email notification" in Advanced settings to get ALERT
when there is a response to you.

your browser is able to open other sites properly right?? try with a diff browser..in your terminal type ping 192.168.1.1 .. are you able to ping?

@matrix
The problem solved ?
if not, in browser
try after entering 192.168.1.1 Id and pw
type 192.168.1.1/menu.html
the following will appear in left side.
......................... to access.

Than you very much essbebe, I am able to see my main page. Now i can control everyting from there. But I have no clue about how this has happened to me. I arrived too late so I am answering now. Thank you once again and all who replied to this thread in particular.

its our pleasure Matrix ...! we are all here to help each other (coz we know BSNL people cant help us LOL)

Para two : 192.168.1.1/look.html
Try again. Post data. This is to check up
whether Firmware update is possible./can be tried
as last resort.
Feedback.

@essbebe

Now it is back to normal, just 192.168.1.1 brings up the main page after id/pwd. Thanks again. See the screen shots. Don't think and firmware update necessary.