Results 1 to 12 of 12

Thread: WA3002G4 taking too long to connect

  1. #1
    Junior Member
    Join Date
    Feb 2009
    Liked
    0 times
    Posts
    19

    Default WA3002G4 taking too long to connect

    Hi all,

    Recently I got the UL 750 Plus plan, and I am given a type 2 modem
    WA3002G4.

    When I switch on the modem, the DSL led blinks, blinks, blinks...for a long long time approximately may be 20 minutes and finally Internt Led blinks green...

    This happens most of the time.
    How can I avoid this problem??

    Reg
    Lee

  2. #2
    kirankumargb
    Guest

    Default

    goto the modem summery page by typing 192.168.1.1 in your browser and when asked for username & password type "admin" in both without quotes, then in summery page goto ADSL there will be SNR ration & Attenuation post those details here... and if your using ADSL2+ type connection change it to G.Dmt ... you can find this also in the modem itself...!

  3. #3
    Junior Member
    Join Date
    Feb 2009
    Liked
    0 times
    Posts
    19

    Default

    The details need to be posted when I am having active internet connection.
    But from last 1 day I am not seeing the internet LED glowing......((
    The DSL led keeps blinking blinking blinking

    Once I get the internet LED up, I can post the details is that correct ?
    Because as of now I don't see any statistics of the ADSL SNR/attenuation values. They are all null values in the 192.168.1.1 page

  4. #4
    meetdilip
    Guest

    Default

    By the time you use the tips from this forum, please register a complaint in your local exchange. May be it is an error from their side. A lot of maintenance is going on in my circle.

  5. #5
    Platinum Member
    Join Date
    Feb 2008
    Liked
    0 times
    Posts
    2,766

    Default

    you need to get your line checked.. i had this issue once.. the lineman had to replace some underground cable .the worst part was that only i was facing this problem

  6. #6
    LEARNER
    Join Date
    Aug 2007
    Liked
    20 times
    Posts
    15,290

    Default

    @leechat2001.
    Presume you are On "Always On" mode
    ( Your UserId and PW entered in the modem )

    2. Start NETWORK LAN Properties
    see Status
    try Repair
    Do you get message IP address not obtained ?

    3. Post
    Start RUN type cmd type Ipconfig /all data

    4. Hope your Phone is working fine.
    .
    5..
    Refer this web site and check modem/router settings are correct.

    h t t p://chennai.bsnl.co.in/BBS/WA3002G4.htm

  7. #7
    Junior Member
    Join Date
    Feb 2009
    Liked
    0 times
    Posts
    19

    Default

    Finally I managed to get the details Statistics -- ADSL

    Downstream Upstream
    SNR Margin (dB): 12.6 7.2
    Attenuation (dB): 24.5 9.6
    Output Power (dBm): 10.9 0.0
    Attainable Rate (Kbps): 18864 340
    Rate (Kbps): 8189 320

  8. #8
    LEARNER
    Join Date
    Aug 2007
    Liked
    20 times
    Posts
    15,290

    Default

    http://i19.tinypic.com/6kqygzt.jpg







    Uncheck only ADSL2+ SAVE reboot.
    Wait for 2 minutes.
    Recheck snr/attn/ etc .
    Last edited by essbebe; 10-06-11 at 07:31 PM.

  9. #9
    Junior Member
    Join Date
    Feb 2009
    Liked
    0 times
    Posts
    19

    Default

    AFter unchecking ADSL2+ Save reboot, following are the values

    SNR Margin (dB):5.7 5.9
    Attenuation (dB): 21.0 9.7
    Output Power (dBm): 12.8 0.0
    Attainable Rate (Kbps): 8116 196
    Rate (Kbps): 8190 192

    Does unchecking ADSL2+ Make difference???
    What one is better?

  10. #10
    LEARNER
    Join Date
    Aug 2007
    Liked
    20 times
    Posts
    15,290

    Default

    When I switch on the modem, the DSL led blinks, blinks, blinks...for a long long time approximately may be 20 minutes and finally Internt Led blinks green...
    From Post No 1.

    Previous one better but likely to be unstable connection.

    1.Mention the mod mode shown on top. GDMT ADSL2+ etc.

    2.List the buttons you have selected. in DSL settings.

    3.Ensure ALL phones are connected AFTER the ADSL
    splitter.

    4. Post ipconfig /all data
    STARTRUN type cmd type
    ipconfig /all


    REF:
    h t t p://chennai.bsnl.co.in/BBS/WA3002G4.htm

  11. #11
    Junior Member
    Join Date
    Feb 2009
    Liked
    0 times
    Posts
    19

    Default

    Hi
    Following are my settings
    Attached Images Attached Images

  12. #12
    meetdilip
    Guest

    Default

    Quote Originally Posted by essbebe View Post

    4. Post ipconfig /all data
    STARTRUN type cmd type
    ipconfig /all
    Quote Originally Posted by essbebe View Post
    3. Post
    Start RUN type cmd type Ipconfig /all data
    s
    Last edited by meetdilip; 05-10-09 at 04:45 PM. Reason: Automerged Doublepost

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Tutorial: How to connect Laptop to TV.
    By imrock in forum Laptop
    Replies: 8
    Last Post: 02-19-10, 09:04 PM
  2. Replies: 7
    Last Post: 02-08-10, 11:53 PM
  3. how to connect ethernet switch between modem and pc
    By horror in forum BSNL broadband
    Replies: 5
    Last Post: 02-03-10, 09:06 PM
  4. How to connect nokia n79 to my pc through wlan
    By shanguy2002 in forum Broadband How to
    Replies: 12
    Last Post: 02-03-10, 12:47 PM
  5. How to connect nokia n79 to my pc through wlan
    By shanguy2002 in forum Aircel Mobile
    Replies: 2
    Last Post: 02-02-10, 04:57 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •