Thread: please help with this Tad 100 ADSL 2.0+

hi all....
Recently i ordered a bsnl broadband service for my pc and the plan is 500c+. I said them that I wil use my old modem and requested to place the connection at the earliest. connection was done and i am unable to connect to net using this modem. I asked bsnl regarding this and they said since the modem was not directly boght from bsnl office, they were not concerned. One of my friend referred me this site and asked to post a rquest regarding this here...

I got a TAD100 ADSL2.0+ modem

please reply me at the earliest so that I can enjoy my net.

Thanks in advance.
Beebatsam

and one more thing...
i have my friends modem for which he dont have adapter and the cable. I got an adapter from another friend through which power is available for the modem and a cable from another friend..
is it necessary that all the three should be of the same company or can i manage with these three different combinations ??????

I connected the modem and tried to access net but unable to access.
I even tried typing 192.168.1.1 in my internet explorer home page but the message is "page not found" please suggest me at the earliest

With power on press the RESET button for about 20 to 30 seconds.
Start Network LAN
properties
Highlight TCP/IP
Properties
enter
192.168.1.10
255.255.255.0
192.168.1.1

DNs 208.67.220.220
208.67.222.222
Apply save.

Open Ie enter 192.168.1.1
admin password admin or password
select WAn page connection 0_35 edit
follow this link for settings

New Page 1

my friends modem for which he dont have adapter and the cable.

Mention modem make/model.

Thanks a lot essbebe for responding....
I will try this and reply in some time......

I did as u mentioned, pressed reset button abt 20 sec and the modem got reset.... but im unable to access modem

did you enter static ip as told by essbebe?? here's a guide on that Prashanth Speaks-Technology and Life: Internet Works on one PC but not on the Other - WINDOWS

my friends modem for which he dont have adapter and the cable

.
Give details. , if stuck on Tad 100.

Hope you made the entries in the computer as told earlier.
Also:
Start/ RUN type cmd type ipconfig /all
give the data here.

My Modem is ADSL2+
Model No. TAD 100
Teracom LTD


ya i made the same entries as u told


h**p://i44.tinypic.com/a243sg.jpg (*=t)

please some one solve my problem so that i can enjoy my net....

Thanks in advance....

Originally Posted by superprash2003

did you enter static ip as told by essbebe??

I did the same as mentioned by essbebe but the same problem
I posted a screenshot of the result when i checked for Run>cmd>ipconfig/all
please see that and suggest me some thing....

Details of my modem are

Product: ADSL 2+ modem/router
Model No. TAD100
Serviced by: Teracom Limited

Step 1> with modem TAD100 connected with power Press the reset button at the back for about 20 or 30 seconds.

Step 2 : connect modem LAN port to ethernet port of Computer with rj45 cable

Step 3 :
Open Internet Explorer browser
enter 192.168.1.1
ID :admin
password : admin (or) password
select WAN page
connection 0_35 edit
follow this link for settings
New Page 1

Para two:
if still no success above.

my friends modem for which he dont have adapter and the cable.

Mention modem make model
to try this instead of TAD100.

modem details are as follows
Product: ADSL 2+ modem/router
Model No. TAD100
Serviced by: Teracom Limited

please anyone come to yahoo and solve my problem...
I am online now my yahoo id is beebatsam@yahoo.com

I am not sure if am havng rj 45 cable or not...
please tell me how to check that..........??

Update;
Your PM.

In your computer :
Start /network/ LAn/properties
TCp/Ip
properties
select
Obtain IP address automatically.
SAVE apply.

Now again check Ip config /all
See whether you can try the modem's IP now
( if not 192.168.1.1)

YOU said you have your friend's mo dem ( call it No 2 modem )
without power adapter and cable.
Wanted the details of this modem
to use it Instead of TAD100

essbebe let me make myself clear about modem i am having...
I am having 2 modems (say a and b)
a modem is TAD100 adsl2+ modem(Teracom Limited)
b is ADSL 2+ modem (Billion electronics limited)

I am having one adapter and one cable. The adapter is able to provide power for both the modems as the lights are blinking when i connect this adapter.

I have a cable which i am not sure if it is rj45 or not... please tell me how to check if the cable is rj45 or not....

You have said the internet worked perfectly , in your PM.
Do the same set up.


A rj11 cable with a single pair of wire is connected to
the adsl splitter LINE from the phone junction

From the ADSL splitter a RJ45 cable ( with 8 wires ) with a slightly bigger connector
is connected from Modem port to computer ether net port.

ALL your telephones connected from PHONE port of
the ADSL splitter

UT-300R2U ADSL MODEM CONNECTION

got it essbebe....
my default gateway is 192.168.4.1 I am able to get that login screen..
Tell me what to do next

got it essbebe....
my default gateway is 192.168.4.1 I am able to get that login screen..
Tell me what to do next

Even if you do not purchase the modem from, it BSNL authorities who should configure your modem. If they do not listen, you can complain to higher authorities or tell them that you will do so.

On the backside of your bill, you will find the phone no of Nodal officer and Appellate authority. They are the highest BSNL authorities available to public. Make a call and seek help.

I called them but they are saying that they will extend their help only to those who bought modem directly from their office and not to anyone others...

to access the modem settings
enter Id as admin

Password as password OR admin
http://i23.tinypic.com/nlpdhs.jpg
A menu page should open

Select WAN page entry 0_35


Select
PPP/PPPoE next
enter your BSNl Id without @ bsnl.in
Password
Always ON"
idle time 0

SAVE REBOOT
wait for two minutes.

Feedback

ya opened....

essbebe,
shold i now change the settings in that page to those as you mentioned earlier in reply#2

ya sure essbebe, I will try and reply you in few minutes..........
Thanks in advance

PPPoE Installation for Bipac 5200S Modem/Router.
For future reference
Open your IE browser and type 192.168.1.1 (can be 192.168.1.254 )

in the URL. Press ENTER to view the login page..

The default user name is admin and
the password is also admin.

The status page will come

change the PVC to PVC2.

Ensure that the status is Activated by selecting
the radio button and ensure
the values of VPI=0 and VCI=35,
the ISP
is set to Bridge Mode and
then the encapsulation is set to
RFC1483 Bridged IP LLC.

Ensure that the radio button
Current Settings
is selected and then
press RESTART to save and reboot the router.

Simply Click OK.

Simply Click OK.

The interface has no log out option and hence click CANCEL and then close the browser subsequently. The modem/router is now set to operate in bridge mode...

Create a PPPoE Connection on the desktop
(Dialing From the Computer)

Thanks a lot to essbebe and this forum leaders....
now my modem is perfectly working.....

Congrats.
Go to Statistics ADSL
post link for a screen shot for that page.

Now find out the power requirements for the billion bipac 5200s modem
what is printed on the unit .
Input 230V ~ Ac output 9 /12 V ~ AC or DC
Polarity for the plug to modem .
inner positive etc.

For Billion...
Input : 12V AC, 1A(Minimum)
Product : ADSL2+ Modem/Router with single port
Model : BIPAC5200S
Billion Electric Co., Ltd.

but I will manage with this TAD100 presently and return back billion to my friend..
If at all I have to use Billion, I will start a thread again in these forums....
Thanks essbebe for your concern.........

@beebatsam

For Billion...
Input : 12V AC, 1A(Minimum

presume Input to modem.

make your friend happy by testing this unit in your computer.
He has to buy a step down AC transformer
230VAC ~ Input Output 12 V A.C~ 1Amp
if he takes the modem to the shop
proper plug can be selected for the modem end.
May cost approx Rs 150 to 200/=

ok i will advice him the same....
Thanks essbebe