India Broadband Forum

meghama

i have a ZTE ZXDSL 831 modem yesterday i reset modem factory restore
and i configure the modem from the configuration details available in after 2 or 3 steps in "service category" configuration my modem has no "UBR WiTHOUT PCR settings .i cannot get net please help menew.JPG


thanks for reply

my modem details
Equipment Vendor ZTE
Model Number ZXDSL 831AII
Firmware Version ZXDSL 831AIIV3.1.0a_D18_IN

it has no service category named UBR without pcr
up loaded the screen shot

Attached Images

	1.JPG (93.1 KB, 22 views)
	2.JPG (98.3 KB, 20 views)

essbebe

in 1.jpg vci is 38 change it to 35.

foribb: CONFIGURING ZTE ZXDSL 831AII IN PPPOE MODE

deepmohan

Reset your modem again and try it.

Refer this document.


1. Connect your computer with LAN cable or USB cable (ensure that the driver of USB should be preinstalled in your computer by the CD provided)
2. Open your internet explorer and type 192.168.1.1 in the address bar. Type the username and password as “admin”.
3. Click Configuration on the LHS, click Internet.

For customers using dialer for broadband
1. Delete the entry with PVC name pppoe_0_35 with the help of the icon provided on the right hand side of this row.
2. After deleting the entry 0/35, click Add on bottom.
3. Edit the VCI value as 35 instead of 38 (service category should be UBR without PCR), click Next.
4. Select Protocol as Bridging with Encapsulation type as LLC/SNAP. Click Next.
5. Leave the IP address page and Click Next.
6. Click Apply. It will take a moment to apply your settings.
7. Click System on Left hand side and click the sub title Reset and Restart.
8. Without checking the check box Reset to factory default settings, click Restart directly to get your modem reboot, after the modem gets rebooted, connect your broadband by using the Dialer on your desktop.

For customer using Always On mode

1. Click edit (Pencil type icon)button in the PVC Name pppoe_0_35.
2. Confirm VCI as 35, click Next.
3. Select Protocol as PPPoE and encapsulation as LLC/SNAP. Click Next.
4. Leave Blank the WAN IP settings and click Next.
5. Type service name as Dataone, Type the Broadband Username, Password and Confirm Password correctly as provided by BSNL. Session established by should be marked as Always on, Click Next.
6. Click Apply, It will take a moment to apply your settings.
7. Click System on Left hand side and click the sub title Reset and Restart.
8. Without checking the check box Reset to factory default settings, click Restart directly to get your modem reboot, after the modem gets rebooted, you are ready to use your internet connection without using dialer.

eruptionjoojo

Hi! bro ...........

actually i read your post ........ but became curious after looking at the screen-shots posted by you of the modem configuration page .......

the screen-shots of your modem have many configuration options while on the contrary i'm having the very same modem type i.e. ZTE ZXDSL 831 AII but the no. of options/settings are far less in comparison.Could you please tell me what is your firmware version etc. of your modem type and which type of connection you are having i.e. always ON/PPPoE or bridge mode/dialing ...........

my Firmware Version is ZXDSL 831AIIV1.0.1i_D18_IN

i'm also attaching the screen-shot of my router/modem configuration page .

Attached Images

Capture.JPG (74.0 KB, 15 views)

meghama

my modem details
Equipment Vendor ZTE
Model Number ZXDSL 831AII
Firmware Version ZXDSL 831AIIV3.1.0a_D18_IN

superprash2003

does the homepage give any error?? like PPP down or authentication failure?

eruptionjoojo

thnxx a lot bro for your reply ..........

so now i'm wondering could you (if possible) upload your firmware to some site so that i can download it and get those additional options ...........

in reference to the difference in firmware versions ........ could you please tell me which city are you from and when did you get the connection etc.

hopefully i'm not troubling you with these questions .........

thnxx in advance ........