Thread: Configuring Beetel 220BX with BSNL dataone

go to ur browser type 192.168.1.1 . enter admin as username and password as password.


click on wan setting and add a new wan configurtion as follows

vpi/vci=0/35

llc encapsulation

choose PPPoE if u want always on connection or

bridge if u want to use XP dialer.

save the settings and reboot the router(compulsory).

hey man plzz first read carefuly wot i m asking or mi english s badd

hey i just read all how to setup airtel beetal modem for bsnl connection
mi problem s i m unable to enter in beetal modem config page

i hve bsnl broadband connection
when i open page 192.168.1.1 it work & bsnl modem page open

but ..when i try to config beetal modem with 192.168... it just
show 401 ur not authorised..
i use user name admin and pass admin
& all four leds r visible
plz help me out

ok now i enter in the beetal modem config page..actualy im wrong

user name ..admin
password..password..

ok i configure it as u all said .. but still nufifng happend.
all four led r steady.. i checked ping its also received data
but no website open
as mi bsnl connection i use user name & password from dialog box to connect mi pc to internet.... but on beetal modem all leds r already blink
eny suggetion

can u post ur screenshot of wan configuration of ur modem

Originally Posted by gurdeep4u

ok now i enter in the beetal modem config page..actualy im wrong

user name ..admin
password..password..

ok i configure it as u all said .. but still nufifng happend.
all four led r steady.. i checked ping its also received data
but no website open
as mi bsnl connection i use user name & password from dialog box to connect mi pc to internet.... but on beetal modem all leds r already blink
eny suggetion

You are getting ping repply ?...but no browsing if so ,
test your DNS by pinging it ( which you entered in modem) can use (change in modem or in pc ) 61.1.96.69 and 61.1.96.71 or use open dns.

hey neeraj finaly i can use beetal...hurrraaaaaa.. actualy prevously im using windows xp dialer.

& just a little configureing...u know i change the setting from

PPPoE over ethernet
to
bridge mode... elss is same as u all guys telme ...

thx a lottttt too alll of uuuuuuuuu

Hi
(I have both Beetel 220BX and UT300R2U) I have tried this steps on Beetel 220BX and and i get all the LEDs are on, DIAG show all pass except USb (not using it) but still i can't get internet.....UT300R2U working fine........

I have this Beetel 2220BX Modem which i was using previously with Airtel. But now i wanna use it with my Dataone Broadband. The Problem is When i plug in the cables and everthing in the modem. It shows limited connectivity and i am unable to login to my Modem. I am very well aware with the other steps after i login into my modem. But when i am getting limited connectivity error. How do i login to my Modem?

I have also tried resetting my modem but nothing seems to be working. Help would be seriously apprciated friends.

try entering ip address manually ..go to control panel->network connections->local area connection properties->tcp/ip properties-> and enter ip as 192.168.1.4 .. and gateway as 192.168.1.1 .. now you shouldnt see limited connectivity.. and you should be able to access your modem at 192.168.1.1

Try reseting the modem also.

Originally Posted by bbkumar

I have a step to step method as of how you can configure your Beetel 220BX modem for BSNL Broadband....


1. First login to your Router using default username and password

2. Click on WAN on the left side menu

3. You'll have options to add or remove configurations.

4. Please select and remove the bridge config as BSNL does not support Bridge.

5. Please click edit on the existing PPPoE Airtel Configuration

6. Set the VPI=0 and VCI=35 (for Airtel it would be 1,32) and click next

7. Select PPP over Ethernet (PPPoE) and encapsulation type: LLC/Snap Bridging and click next

8. Enter the following details:

PPP Username: Your bsnl username (no need to add dataone.in)

PPP Password: Your bsnl password

PPPoE Service Name: DataOne

Authentication Method: Select CHAP

Click Next

9. Check the Enable IGMP Multicast Option

Check Enable WAN Service Option

Enter the Service Name as BSNL

10. Click Next and Save. You should also save and reboot your modem.


And Lo... you can now browse through BSNL broadband!!

hello,

I have made the changes as suggested by bbkumar, my modem is showing internet light on. My test with 'Test ATM OAM F5 segment ping' and 'Test ATM OAM F5 end to end ping' fail and my browser is not connecting to any page.
I am attaching the screen for reference. Plz help.


[IMG]c:\users\Swati\Documents\diagonstics_20080914.jpg[/IMG]


Thanks
Swati

plz find the attached screen

Thanks

@/member/swatikasera
It is OK. For BSNL Diagnostics page .
For Airtel OAM also will show pass.
You can connect to Internet now.
If any problem (see the thread earlier postings by me page 1 or 2 )
Start/ RUN type cmd type ipconfig/all post data here.

http://i21.tinypic.com/33osc9d.jpg

This is the proper setting to change beetal setting

open u r browser
type in url---192.168.1.1
username -admin
password--password
Then open WAN > add > these Account

1) 0/32 in bridge mode

2) 8/35 in bridge mode

3) 8/81 in bridge mode

4) 0/100 in bridge mode

5) 0/35 in pppoe mode > enter u r broadband username & password # pppoe service name - mydslmodem # authentication-- auto #

DISABLE IGMP & WAN SERVICE ....
(DISABLE WAN SERVICE & IGMP both) dont click on them

6) 1/31 in bridge mode

save and reboot

then re open router after 2 min
then go to
LAN >

ENABLE DHCP server

start IP address--192.168.1.1
End IP address -- 192.168.1.21
leased time in hour-- 24

if these seeting help u then please appriciate

all done by----garrysingh
From --ambala cantt(haryana) india

I have configured Airtel Beetel 220BX modem for BSNL and it is working fine. I followed the steps mentioned here. I am using the splitter provided by the BSNL. But when i change the splitter to Beetel(provided by airtel), there is no signal and the LED's are also not glowing.
I have only set up the PPPoE connection. Did I miss anything or I need to change the splitter. Please help.

Thanks,
Anand

Originally Posted by anandsaju

I have configured Airtel Beetel 220BX modem for BSNL and it is working fine. I followed the steps mentioned here. I am using the splitter provided by the BSNL. But when i change the splitter to Beetel(provided by airtel), there is no signal and the LED's are also not glowing.
I have only set up the PPPoE connection. Did I miss anything or I need to change the splitter. Please help.

Thanks,
Anand

Splitter may be malfunctioning. If you already have a splitter that is working, there is no reason to change it or buy a new one.

Beetel 220BX modem for BSNL and it is working fine.

http://i34.tinypic.com/s4c0me.jpg
Check rj11 cables connected properly.
"Funjin "( BSNL) splitter ports are not same.
(reverse)
line ====>>> adsl (left) & phone ( right port )

"beetel" Adsl splitter ( white)
UP " beetel" name left to right
adsl port ( left) LIne ( right )==>PHONE ( singleport)

Using same splitter for the past two years,
for both Airtel and Bsnl BB.
You can/should use the spare for an extension phone
in another room ( if Phone line is concealed wiring )

Hi all,

I'm trying to configure ppoe for beetel modem but unable to complete getting error in Diagnostics:

Test the connection to your DSL service provider:
-------------------------------------------
Test ADSL Synchorization: PASS
Test ATM OAM F5 segment ping: FAIL
Test ATM OAM F5 end-to-end ping: FAIL
-------------------------------------------

Test the connection to your Internet service provider:
-------------------------------------------
Test PPP Server connection: FAIL
Test authentication with ISP: PASS
Test the assigned IP Address: FAIL
Ping Default gateway: PASS
Ping primary DNS: PASS
-------------------------------------------

AND ALSO WHEN IN CHECK THE WAN CONNECTION UNDER DEVICE INFO IT SHOWS AS :

--------------------------------------------------------------------------------------
0/35-off -1 -UBR -BSNL -ppp_0_0_35_1 -ppoE -Enabled -Disabled -Enabled -Up -59.92.134.117(Disconnect)
-------------------------------------------------------------------------------------
i have also done the same setting as mentioned :
-------------------------------------------------------
1. First login to your Router using default username and password

2. Click on WAN on the left side menu

3. You'll have options to add or remove configurations.

4. Please select and remove the bridge config as BSNL does not support Bridge.

5. Please click edit on the existing PPPoE Airtel Configuration

6. Set the VPI=0 and VCI=35 (for Airtel it would be 1,32) and click next

7. Select PPP over Ethernet (PPPoE) and encapsulation type: LLC/Snap Bridging and click next

8. Enter the following details:

PPP Username: Your bsnl username (no need to add dataone.in)

PPP Password: Your bsnl password

PPPoE Service Name: DataOne

Authentication Method: Select CHAP

Click Next

9. Check the Enable IGMP Multicast Option

Check Enable WAN Service Option

Enter the Service Name as BSNL

10. Click Next and Save. You should also save and reboot your modem.


And Lo... you can now browse through BSNL broadband!!
-------------------------------------------------------
Waiting for reply......

@manjupelle
User @anandsaju said

I have configured Airtel Beetel 220BX modem for BSNL and it is working fine.

Problem/discussion is about Splitter use.

Para two:
Kindly address target user example as @essbebe.
I think you are giving a solution,/instructions for Beetel 220BX. for everybody's use. Thanks.

OR

If having still problem connecting
post ipconfig/all data
START/ RUN type cmd type ipconfig/all

Hello I am willing to go for BSNL internet services is it ok. And what is the cost.

Bharat Sanchar Nigam Ltd.

SELECT ACCORDING TO YOUR USAGE/budget/time that can be spent on Internet/special interest movies/music/ chat/ etc.

If you need unlimited UL750 plan at 256Kbps
Home Flexi 350 Home UL 750 Home UL 750 Plus

For faster speed Home 500 series speed upto 2 Mbps
Home 125 Home 250 Home 500 Home 1000.

etc

@yogesh
if you really want to know how good BSNL is .. its best to ask people around you who use it .. As in some areas they have really bad server and customer support .. whereas in other areas , its really good!!

Originally Posted by manjupelle

Hi all,

I'm trying to configure ppoe for beetel modem but unable to complete getting error in Diagnostics:

Test the connection to your DSL service provider:
-------------------------------------------
Test ADSL Synchorization: PASS
Test ATM OAM F5 segment ping: FAIL
Test ATM OAM F5 end-to-end ping: FAIL
-------------------------------------------

Test the connection to your Internet service provider:
-------------------------------------------
Test PPP Server connection: FAIL
Test authentication with ISP: PASS
Test the assigned IP Address: FAIL
Ping Default gateway: PASS
Ping primary DNS: PASS
-------------------------------------------

AND ALSO WHEN IN CHECK THE WAN CONNECTION UNDER DEVICE INFO IT SHOWS AS :

--------------------------------------------------------------------------------------
0/35-off -1 -UBR -BSNL -ppp_0_0_35_1 -ppoE -Enabled -Disabled -Enabled -Up -59.92.134.117(Disconnect)
-------------------------------------------------------------------------------------
i have also done the same setting as mentioned :
-------------------------------------------------------
1. First login to your Router using default username and password

2. Click on WAN on the left side menu

3. You'll have options to add or remove configurations.

4. Please select and remove the bridge config as BSNL does not support Bridge.

5. Please click edit on the existing PPPoE Airtel Configuration

6. Set the VPI=0 and VCI=35 (for Airtel it would be 1,32) and click next

7. Select PPP over Ethernet (PPPoE) and encapsulation type: LLC/Snap Bridging and click next

8. Enter the following details:

PPP Username: Your bsnl username (no need to add dataone.in)

PPP Password: Your bsnl password

PPPoE Service Name: DataOne

Authentication Method: Select CHAP

Click Next

9. Check the Enable IGMP Multicast Option

Check Enable WAN Service Option

Enter the Service Name as BSNL

10. Click Next and Save. You should also save and reboot your modem.


And Lo... you can now browse through BSNL broadband!!
-------------------------------------------------------
Waiting for reply......

I tried so many things as per your instruction, but im still unable to connect to dataone through Beetel 220BX ADSL router. it is still showing ADSL link DOWN
Please anyone help me to solve the problem

Follow the screen shots.
SAVE reboot . Wait for two minutes.
User Id no need to add @ datone in or @ bsnl.in
New Page 1

If all Ok BSNL Gateway will appear in the last screen shot.i as shown in above link. pages.

Feedback.
If still problem :
Post data:

Start RUN type cmd type ipconfig /all

Test ATM OAM F5 segment ping: FAIL
Test ATM OAM F5 end-to-end ping: FAIL

normal for BSNL.

Authentication Method: Select CHAP

Select Auto