Thread: Configuring Beetel 220BX with BSNL dataone

Hai Everybody,
I use a zebronics ADSL modem for dataone internet connection. Due to some problem i cant use the modem. I also have a Beetel 220BX adsl modem with me. I tried to config the modem. But i could not. Also I tried to reset and config it newly. But all in vain. I use BSNL 900 ul+ plan. Also i use ethernet cable to connect. Can anyone guide me to config the modem(Beetel 220BX for dataone broadband) from the reset level.
Thanxs
With regards
Manoj

for PPPOE thru modem

login to modem
select PPPOE
use PVC --> 0 or PVC --> 3
VPI/VCI --> 0/35
disable DHCP
donot worry about other settings at present
give user name & password
save this configuration into modem

configure your network on PC

Gateway 192.168.1.1
IP address 192.168.1.2
subnet mask 255.255.255.0
DNS 61.1.96.69 and 61.1.96.71

now try to connect & report back here .

I have a step to step method as of how you can configure your Beetel 220BX modem for BSNL Broadband....


1. First login to your Router using default username and password

2. Click on WAN on the left side menu

3. You'll have options to add or remove configurations.

4. Please select and remove the bridge config as BSNL does not support Bridge.

5. Please click edit on the existing PPPoE Airtel Configuration

6. Set the VPI=0 and VCI=35 (for Airtel it would be 1,32) and click next

7. Select PPP over Ethernet (PPPoE) and encapsulation type: LLC/Snap Bridging and click next

8. Enter the following details:

PPP Username: Your bsnl username (no need to add dataone.in)

PPP Password: Your bsnl password

PPPoE Service Name: DataOne

Authentication Method: Select CHAP

Click Next

9. Check the Enable IGMP Multicast Option

Check Enable WAN Service Option

Enter the Service Name as BSNL

10. Click Next and Save. You should also save and reboot your modem.


And Lo... you can now browse through BSNL broadband!!

Hi,

I tried the detailed steps you have provided to use beetel 220bx for bsnl broadband but does not work. The only thing i did different was to delete the existing airtel configuration, but i created the new one in the way you have specified. Please let me know if any other settings are to be changed apart from the ones in the wan, like the dsl settings, etc.

Thanks,
Veera

Originally Posted by veerann

Hi,

I tried the detailed steps you have provided to use beetel 220bx for bsnl broadband but does not work. The only thing i did different was to delete the existing airtel configuration, but i created the new one in the way you have specified. Please let me know if any other settings are to be changed apart from the ones in the wan, like the dsl settings, etc.

Thanks,
Veera

Dont delete the airtel config, it bsnl works just fine with that. Have it done redone and let me know

Originally Posted by bbkumar

Dont delete the airtel config, it bsnl works just fine with that. Have it done redone and let me know

I had already deleted airtel config, before i visited your website, later tried to redo the airtel config, and then follow your steps but didn't work, can you let me know other settings to be changed to get it work. thanks.

Originally Posted by bbkumar

I have a step to step method as of how you can configure your Beetel 220BX modem for BSNL Broadband....


1. First login to your Router using default username and password

2. Click on WAN on the left side menu

3. You'll have options to add or remove configurations.

4. Please select and remove the bridge config as BSNL does not support Bridge.

5. Please click edit on the existing PPPoE Airtel Configuration

6. Set the VPI=0 and VCI=35 (for Airtel it would be 1,32) and click next

7. Select PPP over Ethernet (PPPoE) and encapsulation type: LLC/Snap Bridging and click next

8. Enter the following details:

PPP Username: Your bsnl username (no need to add dataone.in)

PPP Password: Your bsnl password

PPPoE Service Name: DataOne

Authentication Method: Select CHAP

Click Next

9. Check the Enable IGMP Multicast Option

Check Enable WAN Service Option

Enter the Service Name as BSNL

10. Click Next and Save. You should also save and reboot your modem.


And Lo... you can now browse through BSNL broadband!!

Hi,
After doing all the steps given, when i check on the WAN status link, it shows "Authentication Failure". I called the BSNL help line to re-set the password but I am still getting the same error. Is there something else which needs to be done?

Open IE type 192.168.1.1/main.html Id admin Password : password
Menu : advanced : Diagnostics :
Check where is the problem.
Or call BSNL to reset the password, if you have configured the modem correctly.

Hi,

How are you getting to the diagnostic tab for the beetel modem? When i log in, my options are LAN status, WAN status, etc. Do not see any options for diagnostics.

In IE type 192.168.1.1/main.html
Clearly shown in screen shot.( diagnostics)

Hi Essbabe,

Thefollowing items show PASS status:
1) test your enet connection
2) Test ADSSl sync
3) Test auth with ISP
4) Ping primary dns

Everything else is in FAIl status with the exception of the USB connection which shows DOWN since I am not using it.

I just now tried to program Beetel220Bx (adsl2+modem) for Dataone for another member (arindan_b )here. It is working fine.
Instead of automatic DNS,1> I unchecked it and entered OpenDNS 208.67.222.222 and 208.67.220.220 :
User name : essbebe ( No @dataone)
Password: xxxxxxx VPI 0 VCI 35 rest almost no change.
.In computer TCP/IP properties select Assign IP address and DNS automatically.
I will post the screen shots in another thread here . by this evening. Please bear with me.
Usually any modem should work with any ISP.

Thanks. Will try this and get back to you. Any settings required in the Advanced set up pages?

In the default page, against WAN status, I am getting Authentication Failure so far. I have called up the help desk and got my password re-set; so it can not be a username/password related issue.

beetel dataone1 see other two screen shots in other thread by arindhan

One more thing to ask.. can you please give a step by step screenshot starting from the above (WAN Setup...clicking Edit button)? I know it is too much to ask.. and it takes considerable amount of time and effort for you.. but if it is possible.. I will be ever greatful
My device info shows 192.168.1.1 for both primary and secondary DNS

After setting up:

Page Wide Area Network ( Wan) setup

VPI/VCI 0/35
service pppoe_0_35_1
Protocol PPPoE
State enabled
Status Up
Ipaddress 59.92.83.160

ATM PVC configuration
VPI 0-255 0
vci0-65535 35

CONNECTION TYPE

click PPP over Ethernet ( PPPoe)

Encapsulation Mode
LLC/SNAP BINDING

PPP username and Password

PPP Username xxxxx : my remark ( no @ dataone.in)
Password zzzzzz
PPPoE Service NAME bsnl
AUTHENTICATION METHOD AUTO

Enable IGMP Multicast and WAN service


select Enable WAN service

Service Name pppoe_0_35_1

WAN set up Summary page

IP address automatically asigned
IGMP and QOS disabled


LUnch and sleep now !

Thanks essbebe...
And last q for the amber light.......... LINK LED
does it glow contenuiously or Blink?

If everything is ok Power red lamp steady
Link amber steady
Data light green blink when data received
PC/USB-- do -- blink when data received

Please confirm ,you got connected to DATAONE with Beetel220BX Adsl2+modem

This is the configuration I am doing:
Edit:
VPI/VCI: 0/35
Service Category: UBR without PCR
QOS: unchecked
Next
Connection type: PPPOE
Encapsulation method: LLC/Snap Bridging
PPP username and password:
Username: xyz
Password: abc
Service Name: PQR
Authentication method: Auto
Dial on demand, PPP IP extension, Use Static IP address, Enable PPP debug mode: All unchecked
Next
Network address translation settings:
Enable NAT: Checked
Enable Firewall : Checked
Enable IGMP multicast: Unchecked
Enable WAN service: Checked
Service Name: pppoe_0_35
Next and Save

Advanced setup for LAN:
DSL router IP and subnet mask have been configured as 192.168.1.1 and 255.255.255.0
Can not see any option called Enable UPnP. Instead, there is an option called Enable IGMP snooping which is unchecked. Also, it is in Standard mode.
DHCP server is enabled with the following settings:
Start IP 192.168.1.3 and end IP 192.168.1.254
Configure the second IP is unchecked.

Advanced set up : Routing
Enable automatic assigned default gateway is checked

Advanced Settings: DNS
Primary DNS server: 208.67.222.222
Secondary DNS server: 208.67.222.220
Advanced settings: DSL
All checked excepting AnnexM enabled
Phone Inner pair
Capability: Bitswap enable and SRA enable are both checked
Am i Missing something?

Originally Posted by souvabhunia

This is the configuration I am doing:

Am i Missing something?

Message received form souvabhunia : for info <br>
Quote Message: Interesting solution - BSNL regularly does something
called "core binding" in which they lock all user ids. After
some time, the ids are released. However, it appears that
the release process is manual and they "forget" to release
some numbers. This can not be done from the BSNL Dataone help desk
and has to be done from the exchange itself. This is what happened in my case.
<br>
Unquote.<br>
Problem solved.

India unlike other countries in the world ( Germany, US) will land on revolution based on internet on mobile. India has a huge potential for mobile based internet. New and new business models will come up like search and adsense on mobiles. I have described my study on comparison between PC and mobile based search in indian context in my blog

Hello,
I configured Beetel modem for DataOne connection. But it has a difference than the UTStarcom modem which is given by BSNL. Beetel require to provide DNS address to be given instead of automatically acquire the same. And the modem keeps on connecting and disconnecting. I dont know why should I give DNS for Beetal model but not for UTstarcom. Both are ADSLmodems.

Please let me know why cant I use same configuration as BSNL modem for Beetel modem?
Anand Krishnan

heyy!! guyz ...help mi out in resolving diz problem
in my digonostic tool it showz
Test ATM OAM F5 segment ping: FAIL
Test ATM OAM F5 end-to-end ping: FAIL

what should i do ..???

It isnt a problem as such
may be becoz of the time u were using it, u got this error
try it again . It will be solved for sure

mi problem s im unable to login to modem..
i hve bsnl connection when i 192.168.1.1 i can see the bsnl modem config. page..
but i got one airtel beetal modem from mi friend..& when i try to 192.168.1.1 i got error message 401 UR NOT AUTHORISED....
can enyone help me