Thread: Wireless not working in WA1003A

Hi,

I have been using Huawei Quidway WA1003A modem for the past 3 years. It has been working fine. Suddenly wireless stopped working. Even if it works, it stops after a couple of minutes. If I look at the wireless stats in the modem, only Rx stats (and FCS as well) increments. Tx stats counters are all zero.

Here is the info on my modem.

Product Information

Model Number WA1003A
USB PID 0x9022
USB VID 0x1110
Ethernet MAC 00:0f:a3:88:de:94
USB MAC 00:0f:a3:88:de:95
USB Host MAC 00:0f:a3:88:de:96
AP MAC 00:50:f1:12:12:10
Software Versions

Gateway V200R002C01B020
ATM Driver 4.05.03.00
DSL HAL 3.02.04.00
DSL Datapump 3.02.06.00 Annex A
SAR HAL 01.07.02
PDSP Firmware 0.49
Wireless Firmware 1.6.0.33
Wireless APDK 5.7.0.5,
Boot Loader 0.22.02

System Log:
=========

DB unloaded !!!

cleanup finish succesfully, good-bye.

Error getting mac from BootLoader enviroment for wlan0

Using default mac address: 00.50.F1.12.12.10

Use BootLoader command:

setenv mac_ap xx.xx.xx.xx.xx.xx

to set mac address

WPA Authenticator Started

Default Asymmetric MTU for wlan0 1500

AP Driver configuration successful

AP IS UP



disabled.

802.11h is 31871: disabled.

Configuration succeeded !!!

WLAN driver database is up

Resetting the remote device.

Un-resetting the remote device.

About to re-init the VLYNQ.

Re-initialized the VLYNQ.

AcxRegAddr = 0xA4040000, AcxMemAddr = 0xA4000000

whal_acxProcInitiate: found DEVICE_VENDOR ID = 0x9066104c

whal_acxProcInitiate: Cpu halt -} download code

whal_acxProcLoadFwImage: 0xa4000000, 0x0

whal_acxProcLoadFwImage() -- Loading FW image31872: Compiled for RADIA (bg) radio

whal_acxProcLoadFwImage: 1, pBuf=0xc00b4f80, len=0x155d8. Extra pBuf=0x0, len=0x3

whal_acxProcLoadFwImage: 2, pBuf=0xc00b4f80, len=0x155d8. Extra pBuf=0x0, len=0x3

whal_acxProcLoadFwImage: 3, pBuf=0xc00b4f80, len=0x155d8, DataLen=0x155d0

whal_acxProcLoadFwImage: 4, pBuf=0xc00b4f80, len=0x155d8

whal_acxProcLoadFwImage: Checksum, calc=0x71f466, file=0x71f466

Mgmt is up

Rx is up

Tx is up

MemMngr is up

main state machine is up

WDRV_MAINSM: WLAN Driver initialized successfully



WDRV_4X: 4x Enabled31903: WDRV_4X: Concatenation Enabled

WDRV_4X: Ack Emulation Disabled

whal_apiStartBss: Enable Tx, Rx and Start the Bss

----------------------------------------------------------------

----------------------------------------------------------------

START BSS, SSID=WA1003A, BSSID=00-50-F1-12-12-10

----------------------------------------------------------------

----------------------------------------------------------------

AP Power Level = 1

Regulatory Domain = ETSI

Net[0] : Channel=1

----------------------------------------------------------------

FW Watchdog is Enabled

Bridge Interface Added: wlan0

Even if I restart my Access Point, I dont see wireless working. Can someone help me on this ?

While most of the data , you have posted, is not understood,
I would suggest check the wireless Lan card and update the drivers.
And in the wlan card configuration, which option has been selected. ? page required.



PS: MTU may be set to 1492