Thread: Siemens c2110 modem problem

Hello friends.. I am facing problem with my Modem (Siemens c2110).
**IT IS ONLY SIEMENS C2110 NOT NOKIA SIEMENS c2110

I am using this modem from past 15 months.. it was working fine.. suddenly the problem starts..

Well, I was trying to re-configure my modem from bridged mode to PPPoE mode.. But i was not successful.. after that my internet connection disconnected. as i was logged in at my modem configuration page i tried to change the settings.. but i was unable to send any queries to the page it was showing an error i.s unable to connect or something. after that i restarted my system and my modem.

after switching on the modem again.. i faced a strange problem. all lights of the modem are ON (power, link, data/usb = red, yellow, green, red. respectively).

When i connect the LAN cable with my modem.. All lights except Power(red) light start blinking.
I have propely configured the tcp/ip propeties.

I tried to reset my modem from that reset switch behind it.. i pressed it for more than 30-40 secs, but i am not sure that the modem had been reset.. "Is there is any way to check that modem have been reset or not"

After this i have again configured the tcp/ip properties. but i am unable to connect the modem configuration page(192.168.1.1). It shows an error (The connection has timed out.
The server at 192.168.1.1 is taking too long to respond.). I m using Firefox. i have tried with other web browser, but the problem is same. I am able to ping my modem (192.168.1.1). I am also not able to connect it through Telnet

My problems are:-
1. Unable to access the modem configuration page.
2. All Modem Lights of modem are keep blinking after connecting LAN cable
3. All Modem Lights of modem are still when not connected with Lan cable

PLEASE PEOPLE HELP ME. LOOKING FORWARD FOR YOUR REPLY

REGARDS,
RAJIV

When you press the reset button for few seconds you will see that all the lights will start to go off except power, when it starts to go off just leave the reset button, once all lights go off and come back thats the indication that your modem has been reset. No need to press it for 30-40 Seconds.

---------------------------------------------
In your TCP/IP Properties provide following:

IP Address: 192.168.1.40 (It can be any value between 192.168.1.3 to 192.168.1.254)

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.1.1

---------------------------------------------
In your TCP/IP Properties provide following:

IP Address: 192.168.1.40 (It can be any value between 192.168.1.3 to 192.168.1.254)

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.1.1

Well i have tried to reset the modem, but the light doesn't goes off and on again.. i lights are still on.. when i connect LAN cable to it the lights start blinking.. My LAN acquires IP but i m unable to open the Modem Configuration page. It shows an error (Unable to connect). I can Ping the modem(192.168.1.1), but cant connect it through telnet or browser

I have configured my IP setting properly. here is the screen-shot of IPCONFIG
img706.imageshack.us/img706/2641/48477805.jpg

C2110 (Type-A) ADSL MODEM MULTIUSER CONFIGURATION
Your dns entry is not correct.



In TCp/Ip properties
enter 8.8.8.8
and 208.67.220.220
apply save.
2. Also in the modem if you access the settings.

Feedback.

I have configured my DNS again as u said.. but i m still unable access my modem configuration page.....

All lights are still blinking after connecting LAN cable...

Your P.M. will try to suggest solutions here.
Change modem default to 192.168.1.2
Download Usb driver. Try USB Ports
Feedback.
OR
default gateway factory settings could be
192.168.0.1

Thanks for your reply brother. but nothing happened the problem is same.. i m unable to access the modem configuration page . I have changed the default gateway ip as u said.. i have tried the both ip-address u have posted. but still i m unable to access the config. page. After changing the default Gateway ip address i tried to ping the address.. but it return me an error "Destination Host Unreachable". But it pings 192.168.1.1 after changing the default gateway ip also.

and all the lights of modem are still ON.

My computer didnt detect new hardware when i connect it to usb.

@Indranil
Your Post has been reported for misuse. out of
thread picture here.
Everytime this thread is opened 160KB D/L for all. ( unless pictures are blocked )

@djniks142

My computer didnt detect new hardware when I connect it to usb.

you may have to uninstall the existing USB drivers for c2110 and , and re install again
( presume you are using some other modem to
connect to internet)
Explain the procedure you adopted.

2.telnet.
I did not enter the password field left it blank.

BCM96338 ADSL Router
Login: admin
Password:
Login incorrect. Try again.
Login: admin
Password:
Login incorrect. Try again.
Login: admin
Password:
> ?

?
help
logout
reboot
adsl
atm
brctl
cat
ddns
df
dumpcfg
echo
ifconfig
kill
arp
defaultgateway
dhcpserver
dns
lan
passwd
ppp
remoteaccess
restoredefault
route
save
swversion
wan
ping
ps
pwd
macaddr
dumpcfg2
clearpsi
sntp
sysinfo
tftp

> defaultgateway

Usage: defaultgateway config auto
defaultgateway config static <[<IP address>] [<interface>]>
defaultgateway show
defaultgateway --help

> defaultgateway show

Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
59.92.64.1 * 255.255.255.255 UH 0 0 0 ppp_0_0_
35_1
192.168.1.0 * 255.255.255.0 U 0 0 0 br0
default 59.92.64.xx 0.0.0.0 UG 0 0 0 ppp_0_0_
35_1

>

3.

Start RUN type cmd
OK
try ipconfig/flushdns
ipconfig/release
ipconfig/renew
then try Modem access.

I have already uninstalled and reinstalled the USB Driver. but still my system didn't detect my modem..

I am unable to connect my modem with Telnet.

I can ping the modem (192.168.1.1)

I have tried your step 3. but still i m not able to open the modem config page.

and Why all Modem Lights (except Power) are still blinking

thats a rocking photo