Results 1 to 11 of 11

Teracom Modem Windows 7 -PpLEASE HELP

  1. #1
    Junior Member
    Join Date
    Jun 2010
    Posts
    24

    Default Teracom Modem Windows 7 -PLEASE HELP

    Hi Friends,

    I had Nokia Siemens Modem which eventually failed and replaced with T2-B-Gawv1.4U10Y-BI.

    I have HP Laptop with Windows 7.

    I have connected the modem with electric supply.

    Now when i type 192.168.1.1 i don't get any page !!!


    Please help me to connect to internet or at least getting connected to Modem homepage.

    Thanks.
    Last edited by sranjanm2002; 2nd August 2010 at 11:19 PM.

  2. #2
    The Wizard meetdilip's Avatar
    Join Date
    Aug 2009
    Posts
    8,776

    Default

    1. Type your external IP in the address bar and check.

    2. Set the values according to this thread

    http://www.indiabroadband.net/broadb...nectivity.html

    Don't get confused by the name.

    3. Reset the modem using the reset button. It will be a small hole in the bottom or rear side of the modem. Power ON the modem and press the hole with a refill. Now you will able to access the modem. You now need to configure it again. Use this guide for PPPoE mode.

    Teracom Type-II ADSL MODEM MULTIUSER CONFIGURATION

    4. Start > Run > cmd >ipconfig/all, post the screen shot.
    Last edited by meetdilip; 2nd August 2010 at 09:31 PM. Reason: Automerged Doublepost

  3. #3
    LEARNER
    Join Date
    Aug 2007
    Posts
    15,263

    Default

    Perhaps you may find the link Terracom, given below useful.
    In computer
    START run type cmd Ok
    New window
    type ipconfig /all
    you will get
    192.168.1. X(x any number 2 to 254)
    255.255.255.0
    192.168.1. X( any number usually 1 for modem )
    see also:
    http://www.indiabroadband.net/broadb...no-access.html

  4. #4
    Junior Member
    Join Date
    Jun 2010
    Posts
    24

    Default

    I am using mobile browser to post query here so will it be ok if i write ipconfig values manually ? Should i write all info including dhcp etc. Thanks.

  5. #5
    The Wizard meetdilip's Avatar
    Join Date
    Aug 2009
    Posts
    8,776

    Default

    No problem. ..............

  6. #6
    Junior Member
    Join Date
    Jun 2010
    Posts
    24

    Default

    I did ipconfig/all but i couln't get data like 192.168, subnet mask etc. I guess if Windows7 laptop would have been connected to modem then only i could have got these things....these are the things that i can see :-

    Primary DNS Suffix=
    mode= hybrid
    ip routing enabled = no
    wins proxy enabled = no
    wireless lan adapter = wireless network 2

    physical address = 00-26-06-51-98-e2
    dhcp=yes
    autoconfig=yes
    connection specific dns=

  7. #7
    The Wizard meetdilip's Avatar
    Join Date
    Aug 2009
    Posts
    8,776

    Default

    1. Tried external IP in address bar ?

    2. If nothing works, reset your modem. Download the guide mentioned in post no, 2. It will help you reconfigure your modem. Please note, after reset, you need to reconfigure your modem to connect to internet.

    3. Did you tried the " limited or no .... " guide. Try it.

  8. #8
    Junior Member
    Join Date
    Jun 2010
    Posts
    24

    Default

    Thanks for the reply.However as i can see WLAN Light is not showing.

  9. #9
    The Wizard meetdilip's Avatar
    Join Date
    Aug 2009
    Posts
    8,776

    Default

    Reset it and try. If modem is faulty, you can get a replacement with BSNL itself.

  10. #10
    Bronze Member
    Join Date
    May 2009
    Posts
    139

    Default windows 7 network config

    log in as admin,
    i am only vaguely familiar with win7, so will give general instructions. these instructions may be related to the classic view of the control panel.
    open control panel, and locate network connections,
    go to the view which lists all network connections (like "Network Connections") in windows XP.

    rt click on the wireless connection and go to properties
    there will be, on the first tab itself, a check box for TCP/IP v6.0.
    uncheck that.
    keep the check box checked for TCP/IP v4.0,

    disable the networks that u do not use.

    in the command prompt shell, type in the following command: -
    netsh int ip reset reset.txt

    restart computer while leaving the modem / router turned on.

    should work for u.

  11. #11
    LEARNER
    Join Date
    Aug 2007
    Posts
    15,263

    Default

    Now when i type 192.168.1.1 i don't get any page !!!
    RESET the modem. Access point may be in bottom of unit.
    http://www.indiabroadband.net/attach...tswitchrt6.jpg

    see link 192.168.1.1 below. and Teracom for settings

Similar Threads

  1. Replies: 1
    Last Post: 8th November 2012, 05:10 PM
  2. VOIP in Teracom Modem
    By lijorijo in forum BSNL broadband
    Replies: 1
    Last Post: 5th May 2011, 06:36 AM
  3. Windows 7 & Teracom incompatiblity Isuue
    By sritcs in forum BSNL broadband
    Replies: 2
    Last Post: 8th December 2010, 09:41 AM
  4. BSNL Teracom modem
    By abhibr95 in forum BSNL broadband
    Replies: 8
    Last Post: 19th November 2010, 07:39 PM
  5. Teracom modem-problematic!!!!!!!!!!!!!!!!
    By getanshub4u in forum BSNL broadband
    Replies: 20
    Last Post: 13th July 2010, 07:16 PM