Thread: D-link DSL-G604T

Can anybody please tell me how to setup DSL-G604T for BSNL Dataone access?

Hi everyone, I could install G604T modem. I can help anyone else with same problem.

^ pls post the procedure here so that it can help the members . thanks

*Setup Wizard*
Run Wizard
Next
New Password: admin
Verify Password: admin
Choose Time Zone: GMT+5:30
Next
Set PPPoE / PPPoA
Connection Type: PPP0E LLC
User Name : "DataoneUsername"@dataone
Password: "Dataone password"
next
Select "Enable Wireless Lan"
next
SSID " choice of ur name to the network"
Channel: 11
Authentication: Open System or Shared key
WEP: Enable
Key Type: Hex
Key Length: 64 bits
Key1 : AAAAAAAAAA
Next
Restart

*Wireless Settings*
Select "Enable AP"
SSID : Your Network Name
SSID Broadcasting: Enabled
Authentication : Open system
WEP: Enable
Key Type: Hex
Key 1: AAAAAAAAAA (or any other 10 hexadecimal digit)


*WAN Seting*
Select PPPoE/PPPoA
User Name: "Dataone User Name" @dataone
Password: "Dataone Password"
Connection Type: PPPoE LLC
MRU: 1492 bytes
Default Rout: Enables
Connection: Connected


ATM VC Settings

PVC : Pvc0
VPI: 0
VCI: 35
Virtual Circuit: Enabled

*LAN*
Management IP

IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0

DHCP Setting:
Select DHCP Server
DHCP Server
Starting IP Address: 192.168.1.1
Ending IP Address: 192.168.1.254
Lease Time: 3600 seconds

DNS Configuration
DNS Relay Selection: Use Auto Discovered DNS Server Only
User Configuration
Prefered DNS Server: 61.1.96.69
Alternate DNS Server: 61.1.96.71

UPnP
Select "Enable UPnP"
Select "connection0"

Tools>Save & Reboot> Reboot

Note: Above settings are for G604T with Firmware Version V1.00B06.AU

Hello,

I have a BSNL Broadband with originally BSNL supplied Huawei MT800 Modem and the connection works fine with the Ethernet cable.

I am now in the process of installing a D-Link DSL-G604T modem with Ethernet as well as Wi-Fi connection. I have followed the procedure given below and am apparently getting connected to the modem by both Ethernet as well as Wi-Fi, however, I am not able to open any Internet page by the web browser using the D-Link modem, although I can quite easily open the pages using the Huawei Modem.

Could anyone help me to further configurate the D-Link Modem to access the web pages?

Thanks in advance for your help....

1Post your ipconfig/all data.

2.What is the error message shown in wireless network page ?

3. Try connecting LAN cableRJ45
from Modem to Lan1 of G604T instead of WANport

Hello essbebe,

Thanks very much for your reply.

In order to give all the information, I thought it would be best to give it to you in pictorial form. Therefore I made
various screenshots of the router configuration and error and other messages as they appear on my screen and there are also two photos of the front and back view of the modem/router as it appears when connected. I put all these in the attached ZIP file.

As you can see I am using a regular RJ-45 cable for connection.

The configuration which I have done are those as given by Ozdesi but it appears my modem is slightly different from the one used by ozdesi.

Awaiting further advice on correct configuration....

in CONNECTION 1.JPG change vpi/vci from 8/35 to 0/35 .. you vpi value should be 0 not 8 .. and once you setup ppoe mode.. you dont have to use the dialer as you have shown in connection through wan ..... .jpg .. by the way , i liked the way you posted screenshots etc , im sure it would be easier for members here to help you out better.. good job..

Hello superprash2003 and everyone...

At I last I have the router functioning both by wire and wireless.

Thanks very much for all your help..

Also, I am glad you liked the idea of posting screen shots.

I am sure it will be useful for anyone requiring reference regarding this unit...