"PPP down" in pppoe mode, but working in briged (dialer) mode

im sure my settings is correct in the router page. i tried to use the "0/32" for pppoe always on. but it says pppoe down. yet when i connect using dialer, i can access the net.

my modem is dareglobal db-108
i want to use the always on mode...

Just reset the modem.

You can select any line but enter and VPI VCI 0 35 for BSNL.

All 8 factory listed lines are set for "BRIDGED" mode and you get connected.
In wan page Select EDIT against 0_35
next page enter vpi vci 0 35
next
enter userid PW etc
SAVE reboot.
Your modem is similar to Beetel 220BX/UT300R2u
check my signature links.

did a factory reset. solved phew.....

i remember i had messed up with settings from the telnet interface..... that was causing the problem i think. a factory reset solved the issue

did a factory reset. solved

Means you could CONNECT in "always On" mode
without entering your USERID/PW in wan Page etc ?????? etc .

i tried to use the "0/32" for pppoe always on.

Your post should confirm the VPI/VCI used etc
( Not 0 and 32 )

i do have a similar situation with D-Link DSL103i modem.
it can work in bridge mode and with miniport PPPOE with a dialer pad configured in connections.
every time we have to call it and click connect. funnily, my messengers 9in auto log in mode) are not allowing me to do the dial up connection until they try fail and give message.
I was not at all able to configure it in PPPOE mode for BSNL even with 0/35 values. I only wonder whether it is a case of firmware corruption. i am told that this is a indian model of DLINK GLB 802

D-Link DSL103i modem. or DLINK GLB 802C
user manual available for GlB802C__________________
http://www.indiabroadband.net/attach...ser-manual.zip
Does the page look like this?
can you select PPPoA/PPPoE option?
http://i221.photobucket.com/albums/d...ation00008.jpg


Para two:
An user reported a rare case, where a "Bridged" connection was set up in VPI/VCI 0 and 32 and a PPP/PPPoE connection on VPI/VCI 0 and 35 for BSNL.
( I had set up for different ISP's airtel ( 1/ 32 and Bsnl 0/35 in same modem)

Assumed/presumed
0 and 32 for VPN connectivity, where normally
you have to use a Dialer to connect with encrypted data.

Yes. The bridge page looks like that only. but the PPPOE once clicked, the fresh page looks different and the LLC is not appearing there.

Can you post screen shot of WAN page?

Even without LLC box did you proceed further ?

In some other old modem also does not appear. for PPP/PPPoE setup.

For reference:
http://mydataone.net/dialer/dlink103i.html

Thanks for Rep + ( could have waited for solution!)

Originally Posted by essbebe

Can you post screen shot of WAN page?

Even without LLC box did you proceed further ?

In some other old modem also does not appear. for PPP/PPPoE setup.

For reference:
The little I know about Dataone Broadband Services offered by BSNL

Thanks for Rep + ( could have waited for solution!)

here are the initial and other 2 pages screen dumps. Rep is for your effort.
results do follow, or, we can get the firmware updated, perhaps.


PS: I fear whether I did hijack OPs post, sorry, if I did so.

Try this powerpoint presentation. about 4MB
same menu pages!!!
http://mp.bsnl.co.in/bb/ut300r2/config300r2.exe

Originally Posted by essbebe

Try this powerpoint presentation. about 4MB
same menu pages!!!
http://mp.bsnl.co.in/bb/ut300r2/config300r2.exe

Thanks for the upload.
Though approximately the pattern is followed. the vpi/vci selection is done on the main page itself in case of DLink DSL103i.
After saving everything, the logging in doesn't happen from the saved name and password in the modem, and it just waits.

Presume you followed exactly the pwer point presentation.
First the default page is Bridged"
then you select PPPoE
then usual entries After APPLY some more steps like tools/etc suggested
Finally reboot the modem.
This is similar to SAVE REBOOT in MANAGEMENT menu
of newer modems.

after rebooting i took a system log with dsl103i
it speaks some sense. perhaps you can guide me from this attached copy as PDF

Originally Posted by essbebe

Presume you followed exactly the pwer point presentation.
First the default page is Bridged"
then you select PPPoE
then usual entries After APPLY some more steps like tools/etc suggested
Finally reboot the modem.
This is similar to SAVE REBOOT in MANAGEMENT menu
of newer modems.

default goes to PPPOE
then i called bridge page set up with 0/35 and dataone as name. LLC enabled
-saved.
later call pppoe and set up as usual without changing pvc etc
still the same errors come up.

the log is listed as below.

Valid Configuration Tree
stat successfull for /etc/resolv.conf.
Resolver Polling Timer Started succesfully.
NTP Polling Timer for DHCP Started succesfully.
DSL Polling Timer Started succesfully.
Firewall NAT service started
del_iptable_rules : ppp_name not intact
Bridge Created: br0
updateall_servers : No children found for conn:
Bridge Created: br1
Bridge Interface Added: eth0
Bridge Interface Added: usb0
DSL Carrier is down
del_iptable_rules : ppp_name not intact
DSL Carrier is up
auto_vcc_default oamPing(0.35)result(2)
auto_vcc_default oamPing(0.32)result(2)
auto_vcc_default oamPing(0.40)result(2)
auto_vcc_default oamPing(0.36)result(2)
auto_vcc_default oamPing(0.38)result(2)
auto_vcc_default oamPing(0.96)result(2)
auto_vcc_search oamPing(0.35)result(2)
auto_vcc_search oamPing(8.35)result(2)
auto_vcc_search oamPing(0.43)result(2)
auto_vcc_search oamPing(0.51)result(2)
auto_vcc_search oamPing(0.59)result(2)
auto_vcc_search oamPing(8.43)result(2)
auto_vcc_search oamPing(8.51)result(2)
auto_vcc_search oamPing(8.59)result(2)
Conn Delay Timer started for 50 sec
pppd 2.4.1 started by root, uid 0
TimerEvent: PPPoE not in a state to handle it; currState 3.

(1)default goes to PPPOE ( enter userid etc then APPLY)
then i called bridge page set up with 0/35 and dataone as name. LLC enabled (* NOT LISTED)
2._____________________
3.___________________
4.____________________________
5.________________________

(-saved)
6__________________
.

List the steps or post screen shots for pages
2 to 6.

Originally Posted by essbebe

List the steps or post screen shots for pages
2 to 6.

I did all the entries as I was doing under GLB502-T that i had earlier.
i have on hand both modems. under similar conditions, 502-T responds and DSL103i fails to respond. how ever i shall be posting images for your analysis.

sry, i was away from home, so couldnt continue with my thread.

hey "0/32" is working fine for me.


but another issue: originally i used to get 32 kbps. i hv the 750 unlimited plan. after i had fiddled with the settings, before resetting,i used to get download speed abt 60 kbps. now its gone back to 32 kbps (i know that is the speed we r supposed to get). but i dunno how i had hacked or sumthing, do u ppl know how to get back that 60 kbps?

Originally Posted by arnab321

sry, i was away from home, so couldnt continue with my thread.

hey "0/32" is working fine for me.


but another issue: originally i used to get 32 kbps. i hv the 750 unlimited plan. after i had fiddled with the settings, before resetting,i used to get download speed abt 60 kbps. now its gone back to 32 kbps (i know that is the speed we r supposed to get). but i dunno how i had hacked or sumthing, do u ppl know how to get back that 60 kbps?

The speed of UL 750 was upgraded to 512 Kbps (64 KBps) in last June. Reset the modem to factory settings and reconfigure it. You will get 60 - 70 KBps on good servers.

Check your speed at speedtest.net and post the " forum link ". Also try a download from Microsoft and report the speed.

@arnab321

From Post No 4.

did a factory reset. solved phew.....

hey "0/32" is working fine for me.

Still on "Dialer" mode ?
or "Always On" PPP/PPPoE mode ?
In computer
Start RUN type cmd
Ok
New window
type ipconfig /all
copy/paste data here.

I m using Dlink GLB-502T modem
I want to configure my modem for internet using Ethernet and USB simultaneously, using PPPoe mode .

I had configured it in PPPoe mode , however my modem doesnt connect to internet automatically?
after configuring in pppoe mode i can see 2 buttons connect and disconnect , what is d use of them , as modem should connect automatically once it is switched on?

can any1 help me out on this..

If you have configured correctly, it will connect automatically. If it is not, there might be some error in your configuration.

You need not use dialer or connect or disconnect buttons in PPPoE mode. In fact, you can delete the dialer and still connect to net. connect and disconnect buttons are irrelevant in PPPoE mode.

This may help

Screenshots - D-Link - GLB-502T (D-Link Firmware) | PcWinTech.com?

Link courtesy essbebe.

Thanks for d prompt reply
i made a new Setup
made following changes,
Name : BSNL
VPI = 0
VCI = 35
entered username and password ..
LAN: Lan group 1

Rest i didnt change..
apply and save all and restart modem..

do i need to disable LAN while doing this configuration ?

Same problem is with me, its not connecting in PPPoE mode at my end as well.

@pkm_sbp
Always mention modem/model/make/number. , you use.

"bridged" in WAN page
Presume you now enter USERID/PW in a "dialer' window in computer to connect to Internet.(

PPPoE ( selected in WAN page) your userid/pw stored in modem/router
and get connected automatically.

Model: DNA-A201BEI

Originally Posted by essbebe

PPPoE ( selected in WAN page) your userid/pw stored in modem/router
and get connected automatically.

I have already stored the UID & Password in router but its not connecting.
There are 2 options to check in it like Enable NAT & Enable Firewall.
So, do i need to check those boxes?

Model: DNA-A201BEI
step by step;
Similar modem ( with wifi.) sl2 _141.
wait...
SL2_141 (Type-B) ADSL MODEM MULTIUSER CONFIGURATION
or screenshots
wait...
Chennai Telephones- Changing password in DataOne Pre-configured modem

Confirm menu pages appear similar for DNA A201BEI.

or like this ? Enable both NAT and firewall.

Originally Posted by essbebe

Chennai Telephones- Changing password in DataOne Pre-configured modem

Confirm menu pages appear similar for DNA A201BEI.

Yup its quite similar to WA 3002 G4.

Problem solved after enabling the above mentioned check boxes.

I have Beetel 450BXI ADSL2+Modem and MTNL triband connection. Each time when i set my router to original default reset, it shows ppp down and there is no internet connection. Each and every light in modem is on that shows the connection is fine, but no internet access.

This is my 3rd time I am facing this problem. still now. Plz help me to get rid of this problem. Thanks.....

After reset follow this link and make settings. For MTNL VPIVCI 0 and 32
Chennai Telephones- Changing password in DataOne Pre-configured modem