Thread: Need help in setting a wireless WIFI connection....

Hello guys i have a Compex MRL21E ADSL modem and an Asus RT-G32 router...So now i need to run internet on my PC and Laptop/I pod touch....

So i was thinking to connect to internet to my PC via modem and wirelessly access to internet through my Laptop and touch....

So please i need help in configuring the settings as i dont know anything about setting up the entire setup.....

I will be very helpful to you if u can solve my problem...

Regards
axxo786

How do you connect now to Internet ?
Using modem compex MRL21E?
( same as Beetel220BXI or Ut300r2U)
(a) In "Dialer" mode login entering UserId/PW in computer window. ?
(b) System gets connected to Internet when desktop and modem switched on
( Called "always On" PPP/PPPoE mode.
Your Userid and PW stored in WAN page of modem )
STEP 1 :
To use wifi mode you have to be in mode (b)

Enable DHCP in lan page and enter 192.168.1.3 to 192.168.1.10
Confirm.
See screen shots ( less wifi settings) in wa 3002-g4 link below.
for compexRL21E( almost similar pages)

Step 2:
Any Installation cd received ? Wizard option ?
http://i53.tinypic.com/1rdnd1.jpg INSERT deleted.
http://i53.tinypic.com/1rdnd1.jpg
on feedback.

Step 3 :
Setup in laptop for wifi Wireless LAN settings.
Mention OS vista/Xp/windows 7 etc.

I connect via the Compex Modem

I think via the PPPoE mode i.e. i give the uesrname and the password provided by my ISP and then click on connect...

And i am using windows 7 on both my laptop and my PC and yes i got a disk with my Asus router....

I want o operate net wirelessly via my laptop and with modem on my PC...

I think via the PPPoE mode i.e. i give the uesrname and the password provided by my ISP and then click on connect...

STEP 1 COMPEX MODEM
This is called "Dialer"Mode also PPPoE and usually "Bridged" in .wan page.
Then you cannot connect your laptop etc.
Please see this link and follow instructions to
be on "ALways On" PPP/PPPOE mode.
(except wifi )

http://clickmakesense.blogspot.com/2...-wireless.html

1A.
Under Advanced Options
WAN page
De select "Bridged" box and select PPP/ over ethernet or PPPoE

Enter your userId ( without @ bsnl.in ) and PW in
wan Page.
In LAN page
select DHCP give range say 192.168.1.3 to 192.168.1.15
Enable UpnP box If seen.
Save
Go to management and click SAVE REBOOT
wait for 2 minutes

Restart system
You will get automatically connected to Internet.
( No need to enter id/pw now)
Confirm connected to Internet.
]
[B]Step 2:[/B}
LAN mode in laptop
Connect Rj45 from desktop to laptop lan port.
Test again .

Step 3 :
Remove Rj45 laptop and connect to
WAN/Internet port of AUS RT-g32
connect another RJ45 from LAN1 to laptop.
RUN wizard and enter wifi settings.

STEP 4:
Test Laptop in wifi mode. remove rj45 and reconnect to desktop.

]Step 5:
Test phone
Feed back Item wise.
if problem copy/paste here. ipconfig /all data needed.
See step 13 in above Blog ( website)

But when i go to 192.168.1.1 and enter the username and password i.e.admin i cannot enter the site ...i.e. the popup window appears again and when i chick cancel it comes
401 Unauthorized
Authorization required.


Note-I am acessing to 192.168.1.1 via my Pc...

id admin PW admin
id admin PW password
id user PW password
id support Pw password.

If you are connected to internet see last link 192.168.1.1
given below in my signature link

Confirm you can download applications and install them.
You only access the system/s as adminstrator.

Thanks mate the page just got opened.. I just can see my Compex modem there...

When i got to Wide Area Network (WAN) Setup

There are so many VPI/VCI so which one do i need to select and edit???

Confirm Step 1
0 and 35 line
and how you accessed 192.168.1.1

step2 to 5 pending

STEP 6:
If Connected to Internet
Again open modem
Go to management
BACKUP ( save) configuration to say
C:/My Documents / compex on lan OK
SAVE REBOOT wait for 2 minutes.

I accessed to 192.168.1.1 via my compex modem i.e. the ethernet cable from my modem goes to my Pc and i am connected to internet while accessing 192.168.1.1...

After step 1 when i rebooted my PC i was not able to automatically connect to my PC...

STEP 7:
Follow steps 1 to 9 in this link.
Click Tric: How to configure UTStarcom wireless router WA3002G4 | WLAN security with MAC address filtering
OR
STEP 1:1A.
Under Advanced Options
WAN page
De select "Bridged" box and select PPP/ over ethernet or PPPoE
_____________________
Enter your userId ( without @ bsnl.in ) and PW in
wan Page._________________________
In LAN page
select DHCP give range say 192.168.1.3 to 192.168.1.15
________________________________
Enable UpnP box If seen.

_______________________
Save
Go to management and click SAVE REBOOT
wait for 2 minutes
_________________________________________
Restart system
You will get automatically connected to Internet.
( No need to enter id/pw now)

________________________________

Confirm connected to Internet.

_____________________________________________

When i saved the WAN settings then i see that

VPI/VCI-0/35
Service-br_0_35
Protocol-PPPoE
State-Enabled
Status-PPP Down

Why is the PPP down here???

Should it be down??

Have you followed POst No 10?
Use quote here
Answer YES DONE or NO.

Originally Posted by essbebe

Have you followed POst No 10?
Use quote here
Answer YES DONE or NO.

YES DONE and now i am automatically connected to the internet...

I didnt understood the Step 2 can u please elaborate more clearly...

STEP 8 old Step 2 .
Check laptop in LAN mode.
(a) connected to Internet YES NO

Does your laptop has a similar rj45 port?
Have you created a LAN connection same way done in desktop ?
Then consider laptop as desktop
and
WITHOUT ANY CHANGES IN MODEM
connect to Laptop. ( remove from desktop end )

Yes connected to internet ...

Now please proceed me to step 3...

Yes i am connected to laptop as i was connected in desktop...

And my laptop have that port...

Step 3 :
Remove Rj45 laptop end and connect to
WAN/Internet port of AUS RT-g32
connect another RJ45 from LAN1 to laptop.
RUN wizard and enter wifi settings. to =

compex Modem RJ45==>> WAN/Internet port of ASUS WIFI
ASUS wifi===LAN1 rj45 to Laptop
ALSO LAN2 rj45 ====>>Desktop. ( if cable available )

Originally Posted by essbebe

Step 3 :
Remove Rj45 laptop end and connect to
WAN/Internet port of AUS RT-g32
connect another RJ45 from LAN1 to laptop.
RUN wizard and enter wifi settings. to =

compex Modem RJ45==>> WAN/Internet port of ASUS WIFI
ASUS wifi===LAN1 rj45 to Laptop
ALSO LAN2 rj45 ====>>Desktop. ( if cable available )

Oki all the cables are connected and wat do i need to do next...

Insert the installation CD
Run Wizard.

Or
http://i53.tinypic.com/1rdnd1.jpg
in Lan first two menu items
In wan first item
Rest all ignore.
STEP 9:

see annexure. only two entries. for wifi
Unsecured now ( simplified )


UPDATE:

STEP 10:
Download USER manual. I will be referring to it
ASUSTeK Computer Inc. - ASUS - ASUS RT-G32.