Thread: how to use 2 wifi modem using single bsnl line

i have a 2 floors in my house. if i want to use ground floor modem on 1st floor then the wifi range is not gud enough and same with 1st floor to ground floor. is there any ways out to use both the modem in single line at the same time?

Yes. Mention modem/router model/make/number.
You have two wifi routers .
Need addditional rj45 cable Probably 5 to 10 meters ( from window side !!!)
Hint:
From LAN1 of GF router connect to WAN port of FF wifi router !
FF unit not connected to Phone line.

utstarcom and the detail are as under
Firmware Version : 2.7.0.31(RUE0.C1)3.5.10.0

i think its type 1 wifi router with 1 lan port in both the router.

If UTstarcom could be UT WA3002_g4. or WA3002_g1
confirm.
check the Device Info given below:. similar ? deleted.
wait...
http://mumbai.mtnl.net.in/triband/ht...ireless_II.pdf

model no is WA3002-G1

try lan 1 to lan1
In FF wifi router wa 3002_g1 in WAN page select "MER"
rest same as in GF wifi router WA3002_g1.
Test in Ground floor with available RJ45 cable.
if successful buy extra cable !

You should get in LAPTOP SSID's given to GFUnit and FF unit . and get connected to Internet.. FFunit used as a switch.

ref http://www.calcutta.bsnl.co.in/dataoneinstall/mu08.html

i didnt get you abt lan1 to lan 1 and where to put the rj45 cable. in GF or FF or in both the router?

A wifi router ( separate unit ) normally has a WAN or Internet port, to which a rj45 from an adsl modem is connected.
from wifi router lan1 to 4 are used for desktops and wifi as usual.
GFUNit connects to Internet normally,
and a minor change
( DHCP to be enabled ) may be rquired .Now no changes.
2.
In this case WA3002-g1 does not have a WAN port.
so we are trying GF Unit LAN1 or Lan 2 to FF unit LAN1
and check whether WIFI mode will work.
Test both in ground floor itself. with available Rj45 cable.
What is the length required from GF to FF ?

what i understand is we have to attach both the router through rj45(ethernet cable) and plug adsl line in GF and then to chk by logging through FF router. one more thing...from where to change 'MER' set up and in which router.

it works or not but many thx for ur kind humble and prompt support....thx buddy

WA33002-G1 to interlink two units for wifi operation

"MER" not needed now.
Also Option NOT AVAILABLE in this model.
( checked in my modem Beetel110TCI ( without wifi same model ) ).

You are /should be connected to Internet with GF unit always.
If one unit is working, you have to duplicate all the entries in the other one. to use it as "stand alone" in First floor. phone line.


Now Unit one SSId is say example Utstarcom
and FF unit SSID say example :Home.
Without making any changes in FF unit , ( but not connected to Phone line ) connect GF lan2 to FF lan1 ( led's blinking normally?)
and check wepultwo appears in laptop.
http://www.indiabroadband.net/attach...fi-data-sm.jpg


Feedback please.
PS: I also like NEGATIVE reports Next time I won't sugggest this !!!.

sorry buddy for replying very late. actually my broadband was not working since the day last we talked. now i have new problem. bsnl people told me to put underscore wcdr after user name and the password will be password because they have shifted my old connection to new server. now the problem is i cannot open few sites in utstarcome w3002 g1 modem. they help line guy came with his modem and everything seems working normally. he said its a problem with some btu which varies from 576 to 1500. before i solve old problem i am into othe deep ****. now you tell me where m i at fault???

b 4 actually i try what you have suggested the connection went down and i was simply helpless. 1 thing more....i will not lie, if i have not replied you then i will confess but this is a genuine fact.

i cannot open few sites in utstarcome w3002 g1
....he said its a problem with some btu which varies from 576 to 1500.

.means MTU. check in WAN page TCP MTU If default is 0 change to 1492.
MSS can remain default 0
http://www.indiabroadband.net/attach...1&d=1310217135

all that thing the bsnl guy tried but not working.

Try tcp/ip optimizer from speedguide.net.
try default values.
enter same in modem page also

they dont have patch for win 7 :-(

they ?dont have patch for win 7 :-(

I am using similar Beetel110TCI and Windows 7 pro.

without any problem.
Await further suggestions from other members .
.

i'll install tcp/optimizer and check if it works or not.

many thx for ur cooperation.

I think you can do it this way. connect the Wifi routers to a 8 port Switch.To this same switch , uplink a cable from the ADSL modem. Configure the routers with plain Wifi Parameters without any routing. configure PPPoE mode in the Modem and configure DHCP. Now whenever you connect to the Wireless, you would get an ip from the DHCP.Since this already PATTed in the ADSL modem, you would get direct internet.

I havent tested this but i think it should work !

Originally Posted by bobbyks2000

I think you can do it this way. connect the Wifi routers to a 8 port Switch.To this same switch , uplink a cable from the ADSL modem. Configure the routers with plain Wifi Parameters without any routing. configure PPPoE mode in the Modem and configure DHCP. Now whenever you connect to the Wireless, you would get an ip from the DHCP.Since this already PATTed in the ADSL modem, you would get direct internet.

I havent tested this but i think it should work !

tats too techno expert kinda job which i dont think i will be able to do it. by the way thanks for your reply.

@wepull8
Back to Base : ( ignore all "Garam Hawa" posted by me !!!)
You have TWO wifi routers.
(1)
one is WA3002_g1 (Post No 5 ) ( say used in "GF") not opening some sites.

(2)
2nd wifi router No details given. ( to be used in "FF" first floor )

(3)

i'll install tcp/optimizer and check if it works or not.

now trying TCP/ip optimizer for No 1.
confirm.
(4)
Reply in method as in (3) above. Please avoid using FULL quotes.
delete in post no 19.