Thread: Configuring UTSTARCOM WA3002G4

Hi folks,

A friend of mine in Kollam, Kerala having a similar modem has a new problem.

His wireless connection to the the modem is on. Skype gets connected, but he is unable to browse. His OS is XP. For the same problem, he had actually reinstalled the OS once and a couple of days later, the problem has surfaced again.

All the relevant lights on the modem are on correctly.

which is his plan?? if its of very low speed.. it could be because skype is using all the bandwidth

Hi superprash2003,

> which is his plan?? if its of very low speed.. it could be because skype is
> using all the bandwidth

It is BSNL broadband upto 2MBPS connection. When it works, it handles Skype + other browsing without problems.

Since yesterday it has been holding on without breaks.

I Tried the above

But they are not working


Device Info

BoardID: 96338W
Software Version: 1132_061507-3.08L.BSNL_02.
Bootloader (CFE) Version: 1.0.37-8.7
Firmware Version: WA3002G4-0021.01
Hardware Version: WA3002G4 1.0
Model Name: WA3002G4
Wireless Driver Version: 3.131.35.6.cpe2.0a.s

This information reflects the current status of your DSL connection.

Line Rate - Upstream (Kbps): 865
Line Rate - Downstream (Kbps): 9919
LAN IP Address: 192.168.1.1
MAC Address:
Default Gateway:
Primary DNS Server: 192.168.1.1
Secondary DNS Server: 192.168.1.1
Date/Time: Sat Jan 1 00:48:55 2000

try this link to check settings of your modem---
BSNL BROADBAND MAIN MENU

Thanks for your response

WA3002G4 is not available

WA3002G2 is available which is not my model

ur downstream is 9919 Kbps
can you say which plan are you using..

settings shouldn't be much different for WA3002G2 & WA3002G4.check that your line mode is G.dmt not ADSL2/2+.

[I am using Dell 1525- Vista]
On the device page:
===============

1. Wireless -- Basic

Enable Wireless - Checked
Hide Access Point - Unchecked
SSID: [Some name]
BSSID: [ Some value]
Country/District: India

Enable Wireless Guest Network - Unchecked
Guest SSID: Guest

2. Security tab

Network Authentication: WPA2 -PSK
WPA Pre-Shared Key: [Gave the key value]
WPA Encryption: AES
WEP Encryption: Disabled

Then clicked save/apply button

3. Management --> Save/Reboot

Now on the computer:
================

1. Start
2. Connect to
3. Select the wireless [with the SSID as mentioned above]
4. Right click and under the security, selected the WPA2-Personal
5. Entered the key

When I connect to internet via ethernet cable, it works.But when I remove the cable it does not work.

Please help

WPA2 sometimes does not work with AES. First try with TKIP (WPA2-TKIP). If that does not work try WPA-TKIP - that will definitely work.

Under Network Authentication, there are below options

Open
Shared
802.1X
WPA
WPA-PSK
WPA2
WPA2 -PSK
Mixed WPA2/WPA
Mixed WPA2/WPA -PSK

So you mean to say, select "WPA2 -PSK" from above and then under "WPA Encryption" select TKIP

No. TKIP is just an algorithm. It is available under WPA, WPA-PSK and WPA2-PSK.

You select WPA-PSK from above options. It will give a further option for algorithms. Select 'TKIP' option and then create the shared key.

Please refer to this guide: Setup of UT-300R2 with Linksys WRT54G

After selecting "WPA2 -PSK" with TKIP encryption, it works.

I wanted to know one more thing:

My Current setting is:
1. Wireless -- Basic

Enable Wireless - Checked
Hide Access Point - Unchecked ==> What is this? Can I check this option?
SSID: [Some name]
BSSID: [ Some value]
Country/District: India

Enable Wireless Guest Network - Unchecked
Guest SSID: Guest

2. Security tab

Network Authentication: WPA2 -PSK
WPA Pre-Shared Key: [Gave the key value]
WPA Encryption: TKIP
WEP Encryption: Disabled ==> Can I enable this? What will happen if I enable this, which key would I have to enter to connect to internet

Please clarify

Please read the "Wireless Security Primers" in the "Broadband How to" section. You queries will be answered.

Can you please give me the link to this thread, I am not able to find it.

Go to the "Broadband How to" section from the Home page.

Found it thanks.:taz:

need help for confg static ip on this modem
it is troubling me when i am downloading with bit torrent . not Abel to connect other peers ....

Dear Ozdesi,

After so many months of reading useless articles and hitting my head into walls after read those, I came across this article, and wow I did whatever is said in this mail and it worked. Now i am using a desktop and laptop simultaneously that too without dialing.

by the way, what is this 1394 connection, i did not have this anywhere in network connections so i missed the network bridging part, but luckily all is working well.

(remember I know nothing about computers, except basic, so these are pretty difficult things for me)

now I want to secure the modem. If anyone has easy to explain articles, then please guide me. otherwise, I will try to find, may be it will also take time.

Anyway big thanks again. Keep up the good work of easy and excellent guiding to people like me.

Hey sonu, please go through the steps that i have mentioned in my earlier posts in this thread

Originally Posted by ozdesi

I was able to set up always on connection with this modem. With this method I do not need to dial the connection every time I boot the PC.

Mind you , this was done on a Desktop with an Ethernet connection to WA3002G4. I am yet to test this with a Wireless Laptop although I have enabled and encrypted WAN. I "think" this should be a multiuser setup.

Here is what I have done.

Go into modem setup from browser (192.168.1.1, admin/admin)

Click Advanced Setup> WAN Setup
Click "Edit" on First Row showing 0/35 under VPI/VCI column.
Uner ATM PVC Configuration
VPI: [0-255]=35
VCI: [1-65535]=35

Enable VLAN Tagging = do not select
Service Category: = UBR without PCR
click next
Select "PPP over Ethernet (PPPoE)" and Encapsulation Mode = "LLC/SNAP-Bridging"
Click Next

Under PPP Username and Password
PPP Username: = <Your Dataonne UserName>
PPP Password: = <Your Dataone Password>
PPPoE Service Name: = Leave this Blank
Authentication Method: = Auto
Do not select anything else on this page.

Enable NAT = yes
Enable Firewall =yes
Enable IGMP Multicast = yes
Enable WAN Service = yes
Service Name =pppoe_0_35_1 (or anything else)
Click next

Now "WAN Setup - Summary" should look like this
VPI / VCI: 0 / 35
Connection Type: PPPoE
Service Name: pppoe_0_35_1
Service Category: UBR
IP Address: Automatically Assigned
Service State: Enabled
NAT: Enabled
Firewall: Enabled
IGMP Multicast: Enabled
Quality Of Service: Disabled

Click "Save".
Click "Save and Reboot" on next page

**Restart your PC and WA3002G4**

Go to "Network Connections"

Select "Local Area Connection" and "1394 Connection" at the same time (hold down control key)
Right click and select "Bridge Connections".
Let windows Create Network Bridge. After few seconds it will shows status as "Connected".

Voila!

hi ozdesi ,
first of all thanks a lot to , write all the details with such a good clarification , really appreciate , actually i was searching that how can i configure my UTstarcom router to keep it always on , on google , i got a link to this site , finally after 8 hours my search ends over hear , but i m happy , finally its done , i have a nokia E61 i handset and now i can access internet on my handset also , but ONLY the last part is remaining , i wiil really appreciate if u help me with this problem also ..Click "Save".
Click "Save and Reboot" on next page

**Restart your PC and WA3002G4**
till this part its fine after this when i select
Go to "Network Connections"

Select "Local Area Connection"
there is no opotion for "1394 Connection" if i ignore that i
Right click and select "Bridge Connections". when i selecting it , it gives me error " To create a network Bridge , you must select at least two lan or high speed internet connection that r not being used by internet connection sharing " lan is not connected but internet is working fine , i guess if the last part is undone is going to be a problem or not , and is there any further securtiy tips to keep my laptop safe because i dont even have antivirus on my system , i m going to purchase it soon , if there is anything else i need to do please tell ,
Yours Sincerely
sagar g

is there any further securtiy tips to keep my laptop safe because i dont even have antivirus on my system[

MOST URGENT
Most Urgent . Download a Firewall program and Antivirus program
and if needed an Anti spyware program.
ALL FREE applications.
Also use ccleaner to keep your computer free of unwanted files.
go to FileHippo.com - Download Free Software and select the programs.
Para two:

i have a nokia E61 i handset and now i can access internet on my handset also

Congrats.
Keep it working. Any other setting changes , if needed,
watch functioning for a week.
If you have a Limited DATA Usage plan, ( other wifi users nearby your
location, can use your connection )
you have to use a security key WPA or WEP to access in WIFI mode.
Please see threads in "Broadband how to ......"
http://www.chennai.bsnl.co.in/BBS/WA...eless_security
Save the settings for future use.

Originally Posted by djrudra

i ran a diagnostic in the router page and this is the result i got..

pppoe_0_35_1 Diagnostics

Your modem is capable of testing your DSL connection. The individual tests are listed below. If a test displays a fail status, click "Rerun Diagnostic Tests" at the bottom of this page to make sure the fail status is consistent. If the test continues to fail, click "Help" and follow the troubleshooting procedures.

Test the connection to your local network
Test your ENET(1-4) Connection: PASS
Test your Wireless Connection: PASS

Test the connection to your DSL service provider
Test ADSL Synchronization: PASS
Test ATM OAM F5 segment ping: PASS
Test ATM OAM F5 end-to-end ping: PASS

Test the connection to your Internet service provider
Test PPP server connection: FAIL
Test authentication with ISP: PASS
Test the assigned IP address: FAIL
Ping default gateway: FAIL
Ping primary Domain Name Server: PASS


what is up with the fail??

i am connected to the net, getting down speeds of 30 kbps(normal??? at least that's what i've got from the beginning...)

why and what is failing??

thanks

ananda

Hai Friends,

If Showing Like same above fail messages in your UTSTARCOM ROUTER, please make Manual IP Configeration in your Computer.

How to change IP address

Click on My Network Places Icon on Desktop --- click View network connections -- Right click on Local Area Connection Icon -- select Properties -- select Internet Protocol (TCP/IP) -- click Properties -- select Use the following IP address -- then change as writtern down…….

IP Address 192.168.1.88(this Number only we can Change 2 –upto 255 ex:192.168.1.89)
Subnet Mask 255.255.255.0
Default gateway 192.168.1.1

Preferred DNS server 193.188.97.196
Alternate DNS server 193.188.97.197

Try to check again Diagnostics in your Utstarcom window (Type Internet explorer 192.168.1.1 ----- enter ----- write username is admin, and the password default is admin or which you created)

Still Not Working Router Please Change as Down:-



Preferred DNS server 193.188.97.196
Alternate DNS server 193.188.95.197

Try to check again Diagnostics in your Utstarcom window (Type Internet explorer 192.168.1.1 ----- enter ----- write username is admin, and the password default is admin or which you created)


Note:- Some Time make Test with OAM it will Work properly

@jojishdas.
I am connected to Airtel on VPI/VCI 1_32.
My modem is also programmed for BSNL Dataone VPI/VCI 0_35.
If in Diagnostics PAGE I click the wrong VPI/VCI result will be shown
as quoted above.
I still work with Airtel connection !

No changes required for IP gateway DNS etc !
I use open dns 208.67.220.220
and 208.67.222.222.

@moderator : for review post no 73.



193.188.97.196 BAHRAIN AL MANAMAH MANAMA 26.236
50.583 - +03:00
Net Speed ISP Domain
- BAHRAIN TELECOMMUNICATION COMPANY BATELCO.COM.BH
IDD Code Area Code Weather Station
973 - BAXX0001 - AL MANAMA

IP Address Country Region City Latitude/
Longitude ZIP Code Time Zone
193.188.97.197 BAHRAIN AL MANAMAH MANAMA 26.236
50.583 - +03:00
Net Speed ISP Domain
- BAHRAIN TELECOMMUNICATION COMPANY BATELCO.COM.BH


IP Address Country Region City Latitude/
Longitude ZIP Code Time Zone
193.188.95.197 JORDAN - - 31.95
35.933 - +02:00
Net Speed ISP Domain
COMP LOCAL INTERNET PROVIDER REGISTRY JOHUD.ORG.JO
IDD Code Area Code Weather Station

Hey Friends,
Is it possible to configure Utstarcom wa3002G4 modem to share files between computer if yes, can anybody help me to configure this modem to share files i have one hp laptop vista loaded with wireless lan and pc with xp pro.