Thread: Configuring UTSTARCOM WA3002G4

Originally Posted by essbebe

1a. Also post From Statistics ADSL
SNR/ATTN/Linespeed /mod selected.

I am providing my modem information in the screenshot named "modem info" and my modem adsl setting in "adsl statistics". Plz provide some solution to my problem

http://i19.tinypic.com/6kqygzt.jpg
1.see this and select only
GDMT T413 glite and bitswap enabled.
2Rest uncheck.
Save reboot. wait for 2 or 3 minutes.

3.Recheck SNR and attn in Statistics/ADSL and report.
4.In Maintenance tr_069 client to be disabled.

Originally Posted by essbebe

1.see this and select only
GDMT T413 glite and bitswap enabled.
2Rest uncheck.
Save reboot. wait for 2 or 3 minutes.

3.Recheck SNR and attn in Statistics/ADSL and report.
4.In Maintenance tr_069 client to be disabled.

Having done all that you've said i am presenting my adsl settings as shown below

is it safe to make this config ?

hello oZdesi

Your post was amazing.....but i cannot seem to reach 192.168.1.1.....it always displays "page cannot be displayed". but i can brows the internet without any issues.....

can you suggest any reasons asto why can't i do so ???

friends please help me. here many people says that 192.168.1.1 site's password and username is admin/admin but i cant enter that site using those password and username. please help me out.

Start Network LAN or wireless LAN
Properties.
Click TCP
properties.
Enable Obtain IP address automatically.
SAVE Apply.

2. Start Run type cmd type ipconfig /all
The default gateway is your modem/router's. .

3. You can reset the router to factory defaults.
( reset button at the back or a
small access round hole in the
bottom)
4. see this web site for settings. again.

Chennai Telephones- Changing password in DataOne Pre-configured modem

Feedback. ( ===>>>another method
without resetting, if 1 & 2 above don't work
and do not want to try 3.
Confirm you get connected to Internet )

mention model no of router.. try admin/password

Originally Posted by ozdesi

I was able to set up always on connection with this modem. With this method I do not need to dial the connection every time I boot the PC.

Mind you , this was done on a Desktop with an Ethernet connection to WA3002G4. I am yet to test this with a Wireless Laptop although I have enabled and encrypted WAN. I "think" this should be a multiuser setup.

Here is what I have done.

Go into modem setup from browser (192.168.1.1, admin/admin)

Click Advanced Setup> WAN Setup
Click "Edit" on First Row showing 0/35 under VPI/VCI column.
Uner ATM PVC Configuration
VPI: [0-255]=35
VCI: [1-65535]=35

Enable VLAN Tagging = do not select
Service Category: = UBR without PCR
click next
Select "PPP over Ethernet (PPPoE)" and Encapsulation Mode = "LLC/SNAP-Bridging"
Click Next

Under PPP Username and Password
PPP Username: = <Your Dataonne UserName>
PPP Password: = <Your Dataone Password>
PPPoE Service Name: = Leave this Blank
Authentication Method: = Auto
Do not select anything else on this page.

Enable NAT = yes
Enable Firewall =yes
Enable IGMP Multicast = yes
Enable WAN Service = yes
Service Name =pppoe_0_35_1 (or anything else)
Click next

Now "WAN Setup - Summary" should look like this
VPI / VCI: 0 / 35
Connection Type: PPPoE
Service Name: pppoe_0_35_1
Service Category: UBR
IP Address: Automatically Assigned
Service State: Enabled
NAT: Enabled
Firewall: Enabled
IGMP Multicast: Enabled
Quality Of Service: Disabled

Click "Save".
Click "Save and Reboot" on next page

**Restart your PC and WA3002G4**

Go to "Network Connections"

Select "Local Area Connection" and "1394 Connection" at the same time (hold down control key)
Right click and select "Bridge Connections".
Let windows Create Network Bridge. After few seconds it will shows status as "Connected".

Voila!

I tried all the above steps and successfull to achieve the following:
1. Connect my desktop PC to internet
2 connect my laptop to internet via both lan cord and Wifi

But the problem stiill facing is that I can not use internet on both PC and laptop simultaneousely.

I have Home 500C plan. Is this a single user plan.
Senior member may please suggest.

1. Connect my desktop PC to internet
2 connect my laptop to internet via both lan cord and Wifi

But the problem stiill facing is that I can not use internet on both PC and laptop simultaneousel

CONGRATS.
For problem above
Hope you have enabled DHCP in the modem
and given arange 192.168.1.3 to say 192.168.1.20

In Your computer and laptop
In TCP/IP properties
select Obtain Ip address automatically.

You may also refer and Bookmark this link if found useful.

http://www.indiabroadband.net/bsnl-b...reference.html (UTSTAR WA3002-G4 quick reference)

Feedback please.

I have followed all steps except the last on i.e to setup bridge connection. I could not find 1394 connection.
My connection is still dialup and I can not connect multiple PC/laptop to internet.
Where I am missing?

My connection is still dialup

Connect in "Always ON" mode.
Which Post or guide you are following now ?

Lan1394 connection not required.

go to control panel->network connections , then go to view network adapters ( or connections or something similar ) and post a screenshot of that page

I just did this, well i changed over from the old single out modem to this one.
And I was having a problem connecting via wifi on my pda.
This just worked well, just edit in the start and the summary, its 0/35 you've written 35/35.
plus I'm noticing a speed fluctuation, does this cause change in speed ?
Anyone noticed the same reply.
Thanks

My Modem is UTSTARCOM UT300R2U.
How to port forward it....?
Does it significantly increases speed.....?

If you are using "Bridged" Dialer Mode all ports are open.
.
If it is a new UT300R2u supplied by BSNL
Port Forward menu item may not be available
Check Under
Advanced Options
Nat
only DMZ may appear.
confirm.

hi. the modem is preconfigured on pppoe and always on mode from factory as username Multiplay.open 192.168.1.1. reset the modem on factory default settings, after reboot click on advance setup. in the table, click on edit in the first line that is vpi/vci 0/35. verify that vpi=o and vci =35. click on next, click on PPPOE over ethernet, next, enter ur username and password, in this page there is an option of always ON next,next, save, save& reboot. it will be configured. please provide security to ur WIfi CONN AS IT IS ALWAYS on.

i have one i phone one laptop, three computers, i want to connect them all to inter net. and the worst thing is my i phone is not connecting to internet. and the site you have told 198.162.1.1 that never opens to change any setting. can anybody help

Try this

http://www.indiabroadband.net/broadb...onnection.html (Solution for multiple machines connecting to same BB connection)

Originally Posted by jitender_2

i have one i phone one laptop, three computers, i want to connect them all to inter net. and the worst thing is my i phone is not connecting to internet. and the site you have told 198.162.1.1 that never opens to change any setting. can anybody help

You will have to assign an ip address manually on the system from which you are trying to access 192.168.1.1

@jitender_2
1.Presume your model is WA3002-G4. confirm.
http://www.indiabroadband.net/bsnl-b...reference.html (UTSTAR WA3002-G4 quick reference)



2.If WA3002-G1 see these links. for WIFI setup.
WA3002-g1 (Type-II) ADSL MODEM MULTIUSER CONFIGURATION



3.
Post this data of your computer if connected to
Internet and working.
Start RUN type cmd Ok
New window
type ipconfig /all
copy/paste data here.
Dont change/blank IP/DNS addresses.

I have updated modem with UT300R2U firmware (version: 3.08.BSNL_02.01.02_tr64._fs_kernel) . So am not able to get wireless option for my WA3002G4. So kindly anyone get the firmware for WA3002G4.. plz mail me.. It can be found in CD given along with UStarcom modem. I dont have that driver CD

kindly mail me the file to

thanks in advance

//Moderator note: You have not activated your account and hence your posts are going into moderation queue. Please click on the link in the mail you received from the forum admin in your mailbox. Failure to do so will cause all your posts go into moderation.
- just4kix

You may have to try a Beetel 450BX modem FW
AT YOUR OWN RISK
Hardware board and menu pages are same.
( minor differences possible )
open 192.168.1.1
then type 192.168.1.1/look.html
to check the present FW version/Software and CFE.

fw UPDATE FOR 450bx.
AT YOUR OWN RISK. repeated!
MEGAUPLOAD - The leading online storage and file delivery service

Unregistered
Guest
I think I have the firmware of WA3002G4
What is your email address
I will email to you.

please send firmware of WA3002G4