Thread: Configuring UTSTARCOM WA3002G4

Write down your email address

thanks man "ozdesi" i was searching various forums for the configuration

the key line was

"PPPoE Service Name: = Leave this Blank"

i previously gave dataone , so guys leave this blank

thanks again

//Moderator note: You have not activated your account and hence your posts are going into moderation queue. Please click on the link in the mail you received from the forum admin in your mailbox. Failure to do so will cause all your posts go into moderation.
- just4kix

Hi guys,
I've been browsing through to get a way to modify my settings to DailUp mode instead of PPPoE. Got somewhat of a picture about it (Thanks to this GREAT site).

But just before i go experimenting, I got a big list other than PPPoE seetings line (plz check screenshot)

Could you tell me what it means?

(Info: I have taken modem on rental basis and seems the warranty seal is broken even before they installed it at home)

CLICK "edit" FIRST ENTRY 0_35
NEW PAGE. UNCHECK ppp/pppOe
SELECT "bRIDGED"
SAVE REBOOT
WAIT FOR TWO MINUTES.
Screen shots available ( less wifi) at this link.
The little I know about Dataone Broadband Services offered by BSNL
2.
Use external Dialer in computer to connect to internet
PPPoE DIALER INSTALLATION
You have to enter your UserID and PW.
Start/Network/ show all connections
A dialer Icon will appear.
3.
Add to Book marks if found useful.
REF:
http://www.indiabroadband.net/bsnl-b...reference.html (UTSTAR WA3002-G4 quick reference)

Originally Posted by raj_cha

Hi guys,
I've been browsing through to get a way to modify my settings to DailUp mode instead of PPPoE. Got somewhat of a picture about it (Thanks to this GREAT site).

But just before i go experimenting, I got a big list other than PPPoE seetings line (plz check screenshot)

Could you tell me what it means?

(Info: I have taken modem on rental basis and seems the warranty seal is broken even before they installed it at home)

as a single user you dont need them and they can be removed except the first one and save the modified file.

Thanks essbebe and that was exactly what i summarised from the site. (Couldnt try it as got exams coming up.)

Again Thanks to sarma, but when you said single user, do you mean i wont be able to use Wifi (browsing & networking-transfering files) if I deleted them (when still in PPPoE Setting)?

And just to confirm,
It will be impossible to connect to internet simultaneously (wifi & lan) when in Bridge mode.


But I also found two options in the PPPoE Settings last page - 'Manual Connect' and 'Dial on Demand' (screen shot attached). what could they be for?

Thanks OzDesi ur Settings WorkEd For ME

Hi there i have bsnl broadband connection using ut starcom modem.i have installed webserver in one of my lan pc. i got static ip from bsnl. when i contact my domain name from outside it goes to modem configuration page because WAN port having the static ip. i need to nat it to my lan pc ip Say 192.168.1.35..
I am unable to do natting plz help me. send ur suggestion to
plzzzzzzzzz

Could someone please walk me through?

Heres what I have

1. BSNL Broadband Home750 plus
2. Modem/Router WA3002G4
3. Connected to Laptop through Ethernet cable RJ45?
4. Telephone line connected through splitter
5. Modem turns on, yellow light steady, WLAN light steady, Green Internet light doesnt turn on blinks sometimes. Doesnt connect to internet
6. Modem purchased in Maharastra, trying to connect the same in Mysore Karnataka. BSNL (Maharastra) had given me a userid and pw (forgotten!)

My questions
1. Do I need a new PW and Userid from BSNL (Mysore)?
2. Can I disable PPPoE for now? How do I do it?
3. Can I change userid and pw myself?

Thanks in advance for all your help.

@diya.
1.
Please see Post No 129 for modem settings.
Report broken links ( website Not available
probably mydataone.in )

2.My questions

1. Do I need a new PW and Userid from BSNL (Mysore)?

YES. Your Telephone number is Changed/circle also changed.
If Interstate transfer of telephone, give the surrender certificate to retain the old BB UserID and PW.
IF your telephone bill was settled, then
fresh telephone Number / BB connection New UserId/PW in Mysore.

2. Can I disable PPPoE for now? How do I do it?

If you are using a Dialer to enter UserID and PW, and don't get connected and get error message , contact CC for new ID and PW.
Or
you have to enter NEW userID/PW in wan page of your router.

3. Can I change userid and pw myself?

NO for USERID & YES for PW
(a) userId probably will be
example xyz06723456
( your telephone number )
(b)Password can be changed later at BSNL Portal ( Another 14digit portalID and PW required )

Feedback.

Thanks. It really worked!

^^^ Please dont issue comments on "Old threads"
please

rest ok.

^ I think bumping old threads is fine as long as it is genuine...

@siddhus212

Thanks. It really worked!

Please mention what worked .
Give Post No. for reference, and member's name.
Almost 140 posts here !
Mention your modem/model/make also.


REF:
http://www.indiabroadband.net/bsnl-b...tml#post208783 (UTSTAR WA3002-G4 quick reference)

i am facing the same problem as Sarath (Kingfisher11111)....WiFi connects fine but eth cable does not and get the nesg "phone line is busy"...line man says some server issue but i never will belv them....any ideas???

Originally Posted by ozdesi

I was able to set up always on connection with this modem. With this method I do not need to dial the connection every time I boot the PC.

Mind you , this was done on a Desktop with an Ethernet connection to WA3002G4. I am yet to test this with a Wireless Laptop although I have enabled and encrypted WAN. I "think" this should be a multiuser setup.

Here is what I have done.

Go into modem setup from browser (192.168.1.1, admin/admin)

Click Advanced Setup> WAN Setup
Click "Edit" on First Row showing 0/35 under VPI/VCI column.
Uner ATM PVC Configuration
VPI: [0-255]=35
VCI: [1-65535]=35

Enable VLAN Tagging = do not select
Service Category: = UBR without PCR
click next
Select "PPP over Ethernet (PPPoE)" and Encapsulation Mode = "LLC/SNAP-Bridging"
Click Next

Under PPP Username and Password
PPP Username: = <Your Dataonne UserName>
PPP Password: = <Your Dataone Password>
PPPoE Service Name: = Leave this Blank
Authentication Method: = Auto
Do not select anything else on this page.

Enable NAT = yes
Enable Firewall =yes
Enable IGMP Multicast = yes
Enable WAN Service = yes
Service Name =pppoe_0_35_1 (or anything else)
Click next

Now "WAN Setup - Summary" should look like this
VPI / VCI: 0 / 35
Connection Type: PPPoE
Service Name: pppoe_0_35_1
Service Category: UBR
IP Address: Automatically Assigned
Service State: Enabled
NAT: Enabled
Firewall: Enabled
IGMP Multicast: Enabled
Quality Of Service: Disabled

Click "Save".
Click "Save and Reboot" on next page

**Restart your PC and WA3002G4**

Go to "Network Connections"

Select "Local Area Connection" and "1394 Connection" at the same time (hold down control key)
Right click and select "Bridge Connections".
Let windows Create Network Bridge. After few seconds it will shows status as "Connected".

Voila!

beetel modem config connection

Dear Frieinds, can any one pls provide me the backup file for WA3002G modem from BSNL, without making the changes. as by chance i had made some changes, and i forget to make a back up file. pls help me yaar. i m from chandigarh.

You can correct settings using this guide

New Page 1

Keep this for reference

http://tinyurl.com/essbebe-wa3002-g4-compilation

check here
for different links with screen shots /step by step Powerpoint /Video
my signature link for WA3002-G4.
UTSTAR WA3002-G4 quick reference
or here:
Chennai Telephones- Changing password in DataOne Pre-configured modem

Originally Posted by ozdesi

Forgot to attach the file.

Save this file as backupsettings.conf

(change the extension to .conf from .txt).

Please note with this configuration I have added WLAN password as "AAAAAAAAAA"

Cheers

hi, i cannot find attachment to download, the shortcut there is directing me to registration ----any suggestion?

see post no 144 or `143 for details about WA3002_g4

Friends i have BSNL Wireless Utstarcom WA 3002G4 and is working fine with my laptop. But i need the modem to configure with my Nintendo Wii Game console to use Internet. While searching, the Game console does detect the modem but is not able to configure itself and keeps asking for MAC address. I have a Mac address at the bottom of the modem but the game console is not accepting and keeps giving me error 52202.

Does anyone here have a Nintendo Wii Game using with BSNL Modem may please help me.

Thanking in advance.