Thread: Setup of ADSL Modem/Router UT-300R2U with Linksys Wireless Router WRT54G

I got my BSNL Broad band connection yesterday.... The lineman just came and gave me the modem (UT300R2U) and said the Username and password are already configured in the modem and left. when i connected the modem the dsl light doesn't comeup. Should i follow these steps? And i dont have the BSNL username or password. Please Help me out. When i called them they said the same again.

thank you

Very very Thankz my brother. u had explained well which i could easily understood and i changed to dialer mode.

I changed my router to dialer modem because am having the rapidshare downloader. In that, they are prescribing the dialer modem for auto switching ip. . so now i changed succesfully to dialup and am downloading from rapidshare of about 21 parts daily night without waking up.

Only because of this i could able to download the files from rapidshare and megaupload without any pain.

Thanks my friend.

Originally Posted by praveenkumar

I got my BSNL Broad band connection yesterday.... The lineman just came and gave me the modem (UT300R2U) and said the Username and password are already configured in the modem and left. when i connected the modem the dsl light doesn't comeup. Should i follow these steps? And i dont have the BSNL username or password. Please Help me out. When i called them they said the same again.

The BSNL person is supposed to install the router and show you that internet is working. But you could do one thing. Use the UT-300R2U CD to install the drivers. The CD does not come with an auto-installer. Browse the CD, and fo the folder which is '\USB Driver\For Windows'. In this folder double click on 'setup.exe' and it will install the drivers. It will guide you when to connect the modem - when it does connect the modem via USB. (follow the router guide supplied with the kit).

After connecting the modem to your PC and open the web setup page (http://192.168.1.1). The page will ask you to login - login as 'admin'; password is 'admin'. Click on the 'WAN' tab.

If what the BSNL man said is correct, then the router must be setup in the PPPoE (always ON) mode. Your username can be found here. The password is 'password'.

DO NOT SAVE ANY CHANGES or CLICK ON THE 'APPLY' BUTTON.

If the modem is already setup (as what BSNL says), then you should be able to connect to internet. In my case, the BSNL person came and installed the drivers, setup the modem, showed that internet is working, left his contact numbers, etc.

To all those who have posted "Thank you" messages, I am sincerely grateful. All I say "You are welcome" in return. Glad to help out for sure.

p/s This is my 200th post.

Dear just4kix, i just had a look at your document and i am amazed at the effort and detail that have gone into it. Without even using it let me say thank you. Let me explain my situation.

I have a UT300R2U, A Netgear WGR614 and a couple of laptops. Now i didn't see your thread, i looked at some other threads that referred to huawei modems, and i fiddled around with a lot of settings on the modem and the router.....and messed everything up. Now the router is broadcasting and i can catch the signal with my laptop and login.....but i have no internet.....neither when connecting with RJ45 straight from modem......nor when it is modem > router > laptop......the "Internet" light on the modem is also off.....does this mean there is no internet signal coming in? or does this mean i've bollocksed it up somehow? please help!!!

One more thing.....when i go to 192.168.1.1 for my modem i get a menu screen and no wizard.....what do i do to get the wizard?

Dear psychotropic, Thanks for the kind words.

I think that it will be best if you start afresh. Please reset both the modems by pressing the RESET switch with bluntly pointed object (do not use sharp pointed objects such as needles).

Keep the "RESET" switch pressed for at least 15 seconds.

After reseting both modems try setup all over again.

thanks for the quick reply......also can you let me know what to do about the fact that i can't get the wizard? The hands-on settings appear to be pretty complex.....thanks in advance

Originally Posted by psychotropic

thanks for the quick reply......also can you let me know what to do about the fact that i can't get the wizard? The hands-on settings appear to be pretty complex.....thanks in advance

I am not sure why you do not get the Wizard. If you do not get the Wizard, click on the WAN tab and select the 'Bridge' option. After selecting this option you do not have to do much. The others are default. Also I am about to post a new guide on this thread: Solution for multiple machines connecting to same BB connection

The topic may be different but the principles are same.

To those of you who said that that ther are unable to get to the 'Wizard' option.

Please do the following:

1. Login to the router page http://192.168.1.1 or http://192.168.1.2
2. Click on the 'WAN' button.
3. Manually enter the following settings:

For Bridging
ATM Interface: PVC-0
VPI: 0
VCI: 35
Virtual Circuit: Enabled
WAN Settings: Bridge Mode
Connection Type: 1483 Bridged IP LLC

For PPPoE
ATM Interface: PVC-0
VPI: 0
VCI: 35
Virtual Circuit: Enabled
WAN Settings: PPPoE/PPPoA
Username: <your ISP username>
Password: <your password>
Connection Type: PPPoE LLC
MRU: 1492
Authentication: PAP
Obtain DNS Automatically: Enabled
Default Route: Enabled
NAT: Enabled
IGMP: Disabled

hi, i reset my modem...but the Internet light is still not on....does that mean the problem is from BSNL's side and not mine?

Originally Posted by psychotropic

hi, i reset my modem...but the Internet light is still not on....does that mean the problem is from BSNL's side and not mine?

Yesterday I was facing this problem and internet was down in my area. It took 6-8 hours to fix. Check out first whether there is problem with intenet service in your area.

If that is not the case, then first try to get the wired connection working. Forget the Netgear equipment for some time, configure the UT-300R2U and check that you are able to connect.

Once UT-300R2U configuration and setup is sorted out, connect the Netgear router and then configure it.

can't figure out anything...internet is still not working in my house....been trying their helpline 1800 424 1600.....haven't gotten through to anyone even once.....have reset the modem multiple times.....don't know what to do.....am really starting to regret going for BSNL.....

Originally Posted by psychotropic

can't figure out anything...internet is still not working in my house....been trying their helpline 1800 424 1600.....haven't gotten through to anyone even once.....have reset the modem multiple times.....don't know what to do.....am really starting to regret going for BSNL.....

If possible, please visit your local exchange. You have paid for a service and you should expect it.

can anyone help me

i want to configure the my pc via lan and usb, actually i have two pc and the bsnl provide me type1 modam and i want to connet my pc by usb and lan.
my one pc is alrady connect via lan cable. but i want to connect my another pc via usb. is it is possible to connect two pc one by ethernet and one by usb, if it is posible, plz help me

i have siemens c2110 adsl modam provided by bsnl.

Yes. It is possible. Note that you may have to configure the modem in PPPoE mode.

Thx a lot

thanks man - I have the UT300R2U but the interface is totally diff to the ones in the pics here - hopefully I can link properly to the info here.

Thanks again for teh great work!!

excellent guide ,thousand pounds of respect to just4kix!!!

Thanks a lot, friends.

hi

many of my friends are having Bsnl broadband...I am also having it

I just wanna know whether we send and receive files through the lan (ethernet or something.....) atleast to comps sorrounding my place

plz help me....

its becoming difficult to carry a pen drive every time....

and also plz let me know if there is any other way to do this if the above method is not possible

Thank u.
I dont have a wireless, but i found it full of good knowledge

Originally Posted by maniram

hi

many of my friends are having Bsnl broadband...I am also having it

I just wanna know whether we send and receive files through the lan (ethernet or something.....) atleast to comps sorrounding my place

plz help me....

its becoming difficult to carry a pen drive every time....

and also plz let me know if there is any other way to do this if the above method is not possible

File sharing is only possible if all computers belong to the same network workgroup or domain.

Originally Posted by navrajyadav

can anyone help me

i want to configure the my pc via lan and usb, actually i have two pc and the bsnl provide me type1 modam and i want to connet my pc by usb and lan.
my one pc is alrady connect via lan cable. but i want to connect my another pc via usb. is it is possible to connect two pc one by ethernet and one by usb, if it is posible, plz help me

i have siemens c2110 adsl modam provided by bsnl.

u have 2 options..

1. buy a broadband router ( ADSL 2+ modem cum router@ 1500+) and a unmanaged switch@700+

2. make one of ur pc a proxy server i.e install 2 lan cards, ccproxy application

bingo...for detail config mail me at prabinseth@gmail.com

Hi

I am using BSNL Broadband Dataone connection with DLINk Modem.
I also bought Linksys Wireless G Router.

The issue is whenever I type the http://192.168.1.1 to get linksys router I always get the Dlink modem interface.

How I can change the settings (configure)for my Router.??. Please advise.

Please note that if I disable the lan connection and enable it back. While The lan connection is enabled, i get the linksys interface for the time being, but as soon as the lan connection is enabled, access to the Router interface is gone and is replaced by modem interface

Please advise