Thread: Help on configuring UTStarcom WA3002-g4

Hello,

I had a Type 3 modem from Huawei. As I wanted to get WiFi, after having bought my laptop.

I could get one "UTStarcom WA3002-g4" modem.

I tried doing what has been told in the manual provided with the modem but in vain.

can you kindly provide me the configuration steps ? Both DSL and Wifi
Is there something additional to be done ??

(I got the modem bought thru my brother in law from a diff. city. Could that be a problem ?)

Regards,
Fifa

hi

1. enter 192.168.1.1 in yout internet explorer
2. when the page opens select " advanced setup'
3. select the connection having vpi/vci vlues as 0/35 and click edit button beside it
4 in the vpi/vci let it remain the same and click next
5. in the connection type select pppOE and click next.
6. enter the username and password given to you in the respective places.
7. click next till the original page with all the connections / having edit button appears.
8. now select the wireless submenu and select basic
9. you can rename the SSID if you want and click save
10. select the security menu and select encrypton enabled with web 64 bits or wep 28 bits, and enter a 10 digit HEX code as the wep key ,it will be the same value that you need to enter in the laptop when your system asks for the wep Key to connect to a ireles n/W
11 .from the maintenence menu select reboot to restart the modm with the selected configurations.

Hey Thank you very much. I shall try these steps and get back to you.

Is that "10 digit HEX code as the wep key" enough to restrict unauthorized access ?

Meanwhile, I have another clarification. Now that I have 2 modems, would it be possible for me to have both of them in operation ?

Originally Posted by fifa

Hey Thank you very much. I shall try these steps and get back to you.

Is that "10 digit HEX code as the wep key" enough to restrict unauthorized access ?

Meanwhile, I have another clarification. Now that I have 2 modems, would it be possible for me to have both of them in operation ?

WPA is better than WEP but that does not mean WEP is bad. Have a look at this article:

WEP vs. WPA

And I have a small section on how to setup WPA security in this guide:

Setup of ADSL Modem/Router UT-300R2U with Linksys Wireless Router WRT54G

Thank you for that reply.

Can you also let me now abt my second question..

"Now that I have 2 modems, would it be possible for me to have both of them operating ?"

Can I try it ? Would it pose any problem if both of them are kept switched on ?

Hi I tried to follow the steps as in changing the WAn settings on WA3002G4 router provided by BSNL but after that the green "internet" light is always ON and when i try to connect using eth to BB it says "phone line is busy", please help??????

yes, when you set your modem to ppoe mode.. you cannot dial from your computer..!!

hey,
I believe that every one might have got the CD along with the package ,
There are few manuals and Trouble shoooting PDFs available that are ofgreat help and are very informative too , they aalso provide the information about configuring the modem in different mode like Brigded, PPPoE,PPPoA and so on.

connecting two modems at a time :

I tink connecting two modems to a single dsl line wont work , and i could not understand the requirement too , what is the purpose , if u could specify your requirement

well your right everybody is supposed to get a CD.. but since we are dealing with BSNL(sarkari).. dont expect everybody to get one.. i got one ..yeah...cool...but it was cracked.. it will broken into 2.. so obv didnt work.. some didnt even get it!!!for some the lineman just brings some modem without box just like some tel cable...

using eth why will i not be able to connect when using pppoe mode???? a type iv router has 4 eth slots too!!

you can.. just connect your computer to the ethernet port of the modem...and if you have configured the modem to work in ppoe mode.. it will work!!

ok...but i am unable to use it as of now...any idea why??? reen internet never goes off

you can connect to the network in two ways
1. Bridged mode : it is similar like a connection between two computers but in case of internet t involves you exclusively dialing , authenticating, obtaining a dynamic IP address and establishing a connection , hence until unless u dont dial u dont get connected.

2. Router mode/ PPPoe mode : in this mode u configure the modem by saving the username and password inthe memory of the modem so that when ever u switch on your modem , it does the part of dialing , authenticating and establishing a connection .


for users having multiple systems connected to the modem its always preferable to connect through the router mode ,in this way you can fully utilize all the ports by connecting multiple peripherls and also equipment like VOIP .

Originally Posted by lakkuMS

hey,
connecting two modems at a time :

I tink connecting two modems to a single dsl line wont work , and i could not understand the requirement too , what is the purpose , if u could specify your requirement

Purpose -

I have a laptop and a PC, each used in diff floors in our home.

I can manage with Wifi but I will have to switch on/off the modem for which i will have to keep going up and down.

Now that I had 2 modems, wanted to know if it could be used in this config.
(As mentioned in this thread, if we use the router config, would it be possible)

@fifa

I had a Type 3 modem from Huawei. As I wanted to get WiFi, after having bought my laptop.
I could get one "UTStarcom WA3002-g4" modem.

Now that I have 2 modems, would it be possible for me to have both of them operating ?"
Can I try it ? Would it pose any problem if both of them are kept switched on ?

No need to keep both of them ON !
Use "Dialup" or "Always On " mode.

1.You can use either of them one at a time independently.

2.Bring a RJ11 cable from Location 1 to Location 2.
( instead of the RJ45 you are using now )
( If Phone Junction already available Use it !)

3.Location 1 : Bsnl Phone Junction. ==>> Rj11 to type III modem => desktop
4.Location 2: Extn Phone line Rj11==>> WA3002-g4-
===>> to laptop either in LAN mode or WIFI mode.
( need addition Adsl Splitter if phone is also used in Location 2 )

5.You can use your laptop at either location (* conditions apply )

6.REF:1 for type III modem. (mention make and model number )
BSNL BROADBAND MAIN MENU
REF 2 : for WA3002-g4
Chennai Telephones- Changing password in DataOne Pre-configured modem

7. Worst case scenerio:
Disconnect RJ11 from one modem !

Thank You very much for the reply.

I already have the phone line running to both the rooms and have connected my modems.

As you mentioned, the current problem is that they both are functional but only being mutually exclusive. (Only one modem would serve).

Can I have both of them operational at the same time ?

Any inputs on the above possibility ??

Can I have both of them operational at the same time ?

YES.

I can manage with Wifi but I will have to switch on/off the modem for which i will have to keep going up and down.

not needed now.

1.''WIFI modem/router always on in say fourth floor
.2......Take a RJ45 cable from here to ground floor ............( max distance possible approx 100 feet or ...............100 meters Don't remember )
3...............Rj45 cable to be connected to desktop ..................LANport.

4. If WIF router switched off , use the other modem Type III ( mention model and make )
as usual in ground floor for the desktop.

i jus got a bsnl connection.. and they configured it like a dial-up with ethernet cable. but the modem i got is wi-fi router... so wen i try to configure.. i am not able to get inside..

wen i enter "192.168.1.1.", it says " the connection to the server was reset while loading" in Firefox.. and in IE, it says "cannot display the webpage", so somebody help me out to access it to de router..

@jayanth100

Start RUN type cmd type ipconfig /all
Check the default Gateway.
Then in IE type that address. admin admin
If modem/router page does not open.
see this link.
The little I know about Dataone Broadband Services offered by BSNL
Take screen shots or copy the values.
If you can follow the instructions, and enter all
values for PPP/PPPoE' AlwaysOn" connection,

RESET the modem to factory defaults.
If the swith or access point is not seen
in rear of unit, see bottom of the unit for a small
round hole.
==================================
@abhayk

using eth why will i not be able to connect when using pppoe mode???? a type iv router has 4 eth slots too!!

Presume eth means ethernet and eth slots are LAN1,2,3, & 4.
pppoe mode means you use a "DIALER".

See POST No. 13 for detailed explanation.

Para two:

How do you connect to the Internet ?
(A)As soon as you switch on the system
and modem/router, do you get connected ?
(In wan page PPP/PPPoE:your userId and PW stored)
Or
(B)You get a "Dialer" screen
where you enter
your UserId and PW and get connected ?
( In the modem "Bridged" is selected )

Para two: How many computers you want to use ?
( you can connect four now )
Any in WIFI method? say a laptop ?

REFERENCE: for those who did not get a CD.
New Page 1
http://www.chennai.bsnl.co.in/BBS/WA...eless_security

check this out

the ips are different.. i mean de default gateway...

one ip showed 0.0.0.0 and the othere 10.3.2.1.

the thing is tht i tried the 10.3.2.1 gateway it still didnt work
:48:

@jayant100
Start
Network
local Area Network
Properties
TCP/IP
properties.
Enter
IP address 192.168.10 (* correction 192.168.1.10)
subnet ;255.255.255.0
Default gateway 192.168.1.1
DNS
obtain automatically or
enter
208.67.220.220 and 208.67.222.222
SAVE apply.

N0W In IE type 192.168.1.1 admin admin
Feedback.

@essbebe
Small typo i guess.. , ip is 192.168.1.10 not 192.168.10 .
@jayanth
Here's a tutorial on the above procedure Prashanth Speaks-Technology and Life: Internet Works on one PC but not on the Other - WINDOWS

@superprash2003.
Thanks for the correction. 192.168.1.10 is correct .
Error regretted.

hi need to know more about the wep key for encrypton since it is supposed to be case sensitive any particular letters or numbers.thanks