Thread: Help:Settings for Wireless connection in WA3002-g1 Wireless ADSL Router

Someone, Please give me the settings for configuring Wifi connection in UTSTARCOM WA3002-g1 Wireless ADSL Router. I use it to connect to my Nokia N91. It connects to my N91, but the page doesn't open and it shows "Services : No gateway reply!".
Please tell me what to do?

When you connect N91 to the router, do you get an IP address assigned to N91?

Originally Posted by just4kix

When you connect N91 to the router, do you get an IP address assigned to N91?

No,i am not sure. In N91,the Ip address is set to automatic.

Originally Posted by charuc14

No,i am not sure. In N91,the Ip address is set to automatic.

Yes. N91 will get an automatic IP address. This IP address must be given to it by the DHCP Server in the wireless modem. So on the N91's wireless connection page, check whether N91 gets the IP address after it has connected.

Modem does not connect to N91 or anything - rather it is the N91 (and other devices) that will connect to modem. As soon as a device connects successfully to the modem, it gets an IP address from DHCP (if the device setting are set for automatic IP address).

Your wireless settings in the modem may not be configured properly.

Originally Posted by just4kix

Yes. N91 will get an automatic IP address. This IP address must be given to it by the DHCP Server in the wireless modem. So on the N91's wireless connection page, check whether N91 gets the IP address after it has connected.

Modem does not connect to N91 or anything - rather it is the N91 (and other devices) that will connect to modem. As soon as a device connects successfully to the modem, it gets an IP address from DHCP (if the device setting are set for automatic IP address).

Your wireless settings in the modem may not be configured properly.

Please tell me where to look for the IP address in my N91. I cannot open the access point while it is connected.
Also tell me about the wireless settings in the modem. I am using Bridge Mode to connect my PC.

These r my wireless settings in my modem.

Wireless LAN
Access Point : Activated
SSID : XXXXXX
Broadcast SSID : Yes
Channel ID : Channel06 2437MHz
Authentication Type : Disabled
Advanced Setting
Beacon Interval : 100
RTS/CTS Threshold: 2347
Fragmentation Threshold : 2346
DTIM : 3
802.11 b/g : 802.11b+g
Wireless MAC Address Filter
Active : Activated
Action : Allow Association
Mac Address #1 : Here i gave my N91's MAC address

Bridge mode will not work because bridge mode allows only one connection at a time. All other connections will have to go through the PC by sharing the internet connection. Try configuration in PPPoE mode.

Note: Wireless security by MAC address filtering is fine but WPA - TKIP is better.

Also refer to my Wireless Security Primers (use forum search).

Originally Posted by just4kix

Bridge mode will not work because bridge mode allows only one connection at a time. All other connections will have to go through the PC by sharing the internet connection. Try configuration in PPPoE mode.

Note: Wireless security by MAC address filtering is fine but WPA - TKIP is better.

Please tell me how to setup PPPoE mode connection.

Originally Posted by charuc14

Please tell me how to setup PPPoE mode connection.

I have changed my connection from Bridge mode to PPPoE mode, but still the same problem,"No gateway reply". Please help me...

just4kix, please help me to connect my N91

Please remove MAC Address filtering from wireless router and implement WPA-TKIP security. My sticky posts in BSNL forums explain how. Also this article may help you: Nokia N95 - "No Gateway Reply" - Here Is How I Fixed It!

Have a look here also: N95 WLAN "No Gateway Reply" : Solution for Ad hoc home Network - Connectivity - Nokia Support Discussions

p/s. Do a google search with the words "No Gateway Reply" (including the quotes).

Originally Posted by just4kix

Have a look here also: N95 WLAN "No Gateway Reply" : Solution for Ad hoc home Network - Connectivity - Nokia Support Discussions

p/s. Do a google search with the words "No Gateway Reply" (including the quotes).

Thanks for ur help just4kix, i just entered the ip address, default gateway manually and it worked out.Thnx once again.

I am glad it has worked out - to be honest I did not do much.

Originally Posted by nandyalas

Hi Can you please help me how to configure this. Thanks

Hi,

Configuring the WA3002 G4
This is a simp0le process
If you have configured your modem in router mode then you can simply add another cable to the PCu require to connect to the Net

Configuring the WA3002 modem _
1. open browser
2. type 192.168.1.1
3. Select the Advanced Setup Tab
4. select the Wan tab
5. Select the first connection given with VPI=0 and VCI =35
6. select the EDIT button
7. give VPI as 0 and VCI as 35
8. Connection type as PPPoE
9. enter the Username and password given by BSNL
10. Check the NAT Enableb and Firewall Checkboxes
11. select save and then save
12. Noew select the Wireless Tab
13. select the security and enable the WEp Encryption as enabled and select the required Encryption type as 64 bits or 128 bits and give the Key as a combination of HEX digits

14.select Miscillaneous tab and click the save and reboot and then click the save and reboot button to reboot the system