Thread: configure my modem wa3002g4 fr always on connection.

am using home 250 plan
i want to configure my modem wa3002g4 fr always on connection.
i want to use 3 pc's at time.

one buddy told me d procedure as follows


"

____________"Click Advanced Setup> WAN Setup
Click "Edit" on First Row showing 0/35 under VPI/VCI column.
Uner ATM PVC Configuration
VPI: [0-255]=35
VCI: [1-65535]=35

Enable VLAN Tagging = do not select
Service Category: = UBR without PCR
click next
Select "PPP over Ethernet (PPPoE)" and Encapsulation Mode = "LLC/SNAP-Bridging"
Click Next

Under PPP Username and Password
PPP Username: = <Your Dataonne UserName>
PPP Password: = <Your Dataone Password>
PPPoE Service Name: = Leave this Blank
Authentication Method: = Auto
Do not select anything else on this page.

Enable NAT = yes
Enable Firewall =yes
Enable IGMP Multicast = yes
Enable WAN Service = yes
Service Name =pppoe_0_35_1 (or anything else)
Click next

Now "WAN Setup - Summary" should look like this
VPI / VCI: 0 / 35
Connection Type: PPPoE
Service Name: pppoe_0_35_1
Service Category: UBR
IP Address: Automatically Assigned
Service State: Enabled
NAT: Enabled
Firewall: Enabled
IGMP Multicast: Enabled
Quality Of Service: Disabled

Click "Save".
Click "Save and Reboot" on next page

**Restart your PC and WA3002G4**

Go to "Network Connections"

Select "Local Area Connection" and "1394 Connection" at the same time (hold down control key)
Right click and select "Bridge Connections".
Let windows Create Network Bridge. After few seconds it will shows status as "Connected".





Bt the problem is tht
i did nt get acces to many sites by this settings
an error message occurs in browser unable to find.
many times.
when i do settings to default of modemsettings it goes right.
all sites open.
at always on connection gives the problem..


plz help me to configure the always on connection propery.

Uner ATM PVC Configuration
VPI: [0-255]=35
VCI: [1-65535]=35

wrong!VPI must be 0

Under PPP Username and Password
PPP Username: = <Your Dataonne UserName>
PPP Password: = <Your Dataone Password>
PPPoE Service Name: = Leave this Blank
Authentication Method: = Auto
Do not select anything else on this page.

where are the dns server addresses in the modem?in pppoe mode you have to manually put these values in modem in the above settings i think.

abov settings given also nt worked.


only selected sites are opening
like google,gmail,yahoo,orkut.
nt

indiabroadband,rapidshare etc.

plz help

did you setup DNS in your modem/router??because if only a few sites open etc.. it could be DNS problem.. try setting it to OpenDns server.. ip's are 208.67.222.22 and 208.67.220.220

OpenDns server.. ip's are 208.67.222.22 and 208.67.220.220

its 208.67.222.222 and 208.67.220.220

Originally Posted by whitestar_999

its 208.67.222.222 and 208.67.220.220

where can i configure DNS server adress
and also hw to bridge local area and 1394 conn

where to configure the dns server address
and wat is 1394 connection
hw can i bridge it wit local area conn

where can i config the dns server address
and wat is a 1394 connection. shld i bridge it wit my local area connection>??

From your queries , unable to understand what is the problem.
confirm you are connected to internet and can surf now
IF not;
see this link and follow the settings.

Chennai Telephones- Changing password in DataOne Pre-configured modem

Para two :

(a)DNS entries can be entered in the modem .
Advanced settings DNS
h t t p://i23.tinypic.com/oidiro.jpg (* http without space)

(b) Also in TCP/IP properties page in computer.
Start/network/LAN properties
TCP/IP properties.

Para three : 1394 connection.
http://computer.howstuffworks.com/question371.htm

Not needed. for a single computer.
How many computers/other devices you are using ?

Feedback.

essbebe has said it all!

but just to be short there's a high possiblity that there is a DNS problem, if you are not able to set dns servers in your modem config. then do that in the LAN options simple

and as far as my memory serves me right 1394 connection if for the inbuilt modem(56 Kbps) in which you connect your telephone line, there is no need to bridge that.....sheeesh

can anyone help to configure BOSS linux to use bsnl broadband

when you were in windows , did you use a dialer to connect to the internet or did the internet work as soon as you switched on your modem? in your terminal , type ifconfig and post output.

i DInt uNDeRsTANd

pLEAsE hEl{p Me by gIving baCkuP sETTInGS