Thread: Dataone Broadband Connection Night Free Manager Download

i used your software yesterday and i slept well .i have plan 500C at home now see the result.i lost 180 MB FROM my free 1500MB.IN KERALA they will charge you if you connect even seconds before 2AM
AS you have given in documentation your s/re disconnected at 1 .57 but bsnl counted from 1.57 ,(when it was connected again ) to 2.27 thats their ,say ,one pulse or interval ,and they counted the downloaded data,i will sent the sceen shot then this problem will be obvious.

i had this problem every month and when i complainted ,nothing happened .there is some problem with their internal system clock.
even if you connect at sharp 2.am say IST ,you will be counted,so i used to connect at 2.05 am then no problem.
there is some 2 or 3 minutes diff in their clock

i lost 180 mb , surely this is not a great loss ,but still what your software claim is wrong
i have a little suggestion change the time setting from 2.05 AM to 7.57 AM.
This is the ' safe period' for BSNL .No problem during this time

Sreejith

TRY.
set your computer clock 5 or 10 minutes slow !
presume d/l till 0805/0810 ( as per correct time )
will not be counted .
The usage meter reads in block of 30 minutes.
(during change over time/s.???)
For instance if you start at 0755 and end at 0850
your usage 0755 to 0825 will not be counted.
You may get two sessions. ( this is a reported "BUG")
0755 - 0825 and 0825 -0850.
test with a small file or just surf.

i will try and will inform the results

ps:thanks for the reply..i have experienced the bug you reported,infact the BSNL section told me about that,but not as a bug

Reset your computer clock late by say 7 minutes.
Then when correct time is 0200 for you PGM D/L will not start it will start at 0207.
When correct time is 0800 it will not end will end at 0807 !
( usage 0800-0807 correct time will not count ).

When your tariff plan is NU free 0200-0800 , if the usage meter is not
programmed to note this fact and works with 30 minutes block as usual it is called a "BUG". Programmer has to change the instructions.
If Tariff plan is home 500.
stop usage count at 0200 restart new block at 0200 else
continue . or settings to this effect.
IN Airtel, my NU is not shown.

Thanks , lemme check it

If I am downloading a movie or something around 1:30 AM - which showing downloading remaining time an hour and above - will it continue after automatic switching on(or disconnecting) and reconnecting?

All downloading sites are not allowing pausing the download. What will the DataOne manager do?

i dunno wat to with this software .please help in detail.my place is mysore karnataka n my modem is ut300r2u

@manojsbhat.
This program is for automating downloads during
Night usage Free allowed during 0200-0800AM. ( Home 500 etc )
If your tariff plan is UL750 unlimited etc , no need for this software.

Originally Posted by sreejithviswam

i used your software yesterday and i slept well .i have plan 500C at home now see the result.i lost 180 MB FROM my free 1500MB.IN KERALA they will charge you if you connect even seconds before 2AM
AS you have given in documentation your s/re disconnected at 1 .57 but bsnl counted from 1.57 ,(when it was connected again ) to 2.27 thats their ,say ,one pulse or interval ,and they counted the downloaded data,i will sent the sceen shot then this problem will be obvious.

i had this problem every month and when i complainted ,nothing happened .there is some problem with their internal system clock.
even if you connect at sharp 2.am say IST ,you will be counted,so i used to connect at 2.05 am then no problem.
there is some 2 or 3 minutes diff in their clock

i lost 180 mb , surely this is not a great loss ,but still what your software claim is wrong
i have a little suggestion change the time setting from 2.05 AM to 7.57 AM.
This is the ' safe period' for BSNL .No problem during this time

Sreejith

the problem is with your clock.... try syncing your your clock with time.nist.gov. you can start your session at 2:00 and stop at 8:00. there wont be any problem.. i have been doing that for quite sometime now.

Originally Posted by bijeshn

the problem is with your clock.... try syncing your your clock with time.nist.gov. you can start your session at 2:00 and stop at 8:00. there wont be any problem.. i have been doing that for quite sometime now.

are u sure if i use dial up at 2 30 am,but keeping modem on from 10 pm it will be counted as free

yes you can.

conditions are:
your router shouldnt be PPPoE. if it is, then i guarantee you that you will be billed!. if it is, change your router into a bridged router. how to do that is given in a new thread by me: Broadband night-free scheduler with Siemens C2110.

you do this and schedule your connection to disconnect at 7:59 after syncing your clock.


i connect at 2:04, to allow for bootup and disconnect at 7:59.

Thanks

can i use this download manager for my dlink 2640 T configured on PPPoE

thanks for this interesting software

dear All,


I am using business plan3000, this nite 2am to 6am plan is working to that business plan...

please tell me any one

Regards,
naga Satish.k

Wow thats nice software, Actually we need these types of softwares

its looks like a grt post i have had problems in the past , used to switch on my modem in the night and used to go to sleep and switch it off at 8 am , suddenly at the end of the month i found that my download limit was exceeded.

some one please help, i have installed data one manager ,problem is manual connect and discoonnect working, but how to schedule, i,m using auto power on & off for scheduling. my windows scheduler is having some problem and to schedule any task.

please help .

Is it really necessary to reboot your modem?
Enabling and disabling the network adapter will not do the trick? Please confirm.

ya i hope it will work , but how do u do that daily at 2.10 am ??

I am using a utility called devcon.exe. I used to schedule task for 2.30 AM.
Please use google to get more info about devcon.exe.

are u able to download safely using the devcon utility ? , by disabling and enabling the conncection session getting restarted ?

do we need a bridge connection for using this software???

thanksssss friend Im gonna try it now....!

Yes mate absolutely correct i hav faced this f*** problem lot of time when i schedule my downloads