India Broadband

whitestar_999

dhcp must be enabled in ut300rtu & set its range from 192.168.1.2-192.168.1.100
change IP address of router to 192.168.2.1
router must be setup in pppoe mode.

one of just4kix's replies---

__________________
"They say that if you play a microsoft disc backwards you hear satanic messages, thats nothing: if you play it forwards it installs windows"

wecaz

Hi,
I am going to buy Netgear Router WPN824. Can somebody tell me whether it can be configured with BSNL broadband. Netgear Router WPN824 is only a router without a modem.

superprash2003

yes it can be used.. Lot of tutorials from just4kix here..

whitestar_999

@wecaz,also router can not be used without a modem for an internet connection so you have to setup your router after connecting it to modem for bsnl broadband.

purnendu@gmail.com

Hello ,
I have been still not able to configure it, so i start from scratch again.
Please find attached the WAN configuration in my modem by default.Do i need to have all of them enabled ? Also please
note the "authentication failure" under ppoe. Is it the problem? However i am able to connect to internet with this
settings.

Attached Files

factory_default.zip (80.7 KB, 8 views)

whitestar_999

authentication failure shows that something is wrong with your bsnl username/password.enter your bsnl username without @bsnl.in & then try but then you can not possibly connect to net.also if the connection shows you are connected to net it also usually shows the IP address in front of connection which is empty in the pic you posted.run ipconfig /all & post the results because i am not getting how you can connect to net even after authentication failure error.

just4kix

Here is the guide that you are looking for: http://www.indiabroadband.net/bsnl-b...-wgr614v7.html (Setup of UT-300R2 with Netgear WGR614v7)

purnendu@gmail.com

Hello whitestar_999,
It seems strange to me also that how can i access the internet with authentication failure. Please find below the ipconfig/all information below.

Windows IP Configuration

Host Name . . . . . . . . . . . . : moumitaghosh
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Wireless Network Connection:

Media State . . . . . . . . . . . : Media disconnected
Description . . . . . . . . . . . : Broadcom 802.11b/g WLAN
Physical Address. . . . . . . . . : 00-1A-73-2F-1C-7F

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Realtek RTL8139/810x Family Fast Ethernet NIC
Physical Address. . . . . . . . . : 00-16-D4-BF-15-7A
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.1.2
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : 192.168.1.1

PPP adapter Broadband Connection 3:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface
Physical Address. . . . . . . . . : 00-53-45-00-00-00
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 59.93.170.137
Subnet Mask . . . . . . . . . . . : 255.255.255.255
Default Gateway . . . . . . . . . : 59.93.170.137
DNS Servers . . . . . . . . . . . : 218.248.240.23
218.248.240.141
NetBIOS over Tcpip. . . . . . . . : Disabled

whitestar_999

seeing your results it seems that you are not using pppoe mode but bridge mode.if that is the case then you have to simply connect router to modem & then setup your modem in pppoe mode by entering your bsnl username/password in router itself.also be sure to first connect only router to computer & configure it in pppoe mode then change the LAN IP address of router to 192.168.2.1 & similarly change the Ip address to something like 192.168.2.4 in computer LAN settings & put gateway & dns as 192.168.2.1(pointing to router).now put the gateway/dns server as 192.168.1.1(pointing to modem)in router LAN settings.after this connect modem to router & you should be able to access now both modem & router from computer.
first do this & see if you can now access modem from computer.

purnendu@gmail.com

Hello whitestar_999,
Thanks for the suggestion. But i am still not able to connect. I tried resetting my netgear router.
Upon running the setup wizard , it automatically detects the connection type as "PPOE". But when its trying to test it , it fails. Also if i try manualy to setup a connection the router says "No PPOE server detected"


~purnendu