Thread: utstarcom modem confi

hello friends,
i have bsnl broadband connection with utstarcom modem wa3002g4. i want to configure my modem to autometic mode to connect my htc wifi phone but i was unable to open the configraton page of modem i.e 192.168.1.1 i have tried by changing the ip in TCP/IP settings of modem properties but all my attempts failed. i have tried ping –c 8 192.168.1.1 through RUN but the DOS just flikered and gone. can anyone here tell me how to open confi page of modem and how to configure PPPOe to connect htc wifi phone.

You may wish to refer and post on this thread: http://www.indiabroadband.net/bsnl-b...-wa3002g4.html (Configuring UTSTARCOM WA3002G4)

i said i was unable to open 192.188.1.1 then what is use of u'r link

go to the command prompt(start->run and type cmd).. and type ipconfig and post output here..a screenshot would do..

Window ip configuration

Ethernet adapter wirless network connection 2:

connection-specific DNS suffix-------:
IP Address--------------------------: 192.168.0.1
subnet mask------------------------: 255.255.255.0
Default Gateway--------------------:

PPP adapter dataone 2:

connection-specific DNS suffix.:
IP Address--------------------------:117.195.164.245
subnet Mask------------------------: 255.255.255.255
Default Gateway---------------------: 117.195.164.245

--------------------------------------------------------------------------
i request u to answer soon

try typing 192.168.0.1 .......if this doesnt work just check this ,your modem must be detected by your computer in "my network places",if it is not being detected then you cant open your routers config. page

also try to change your ip address in control panel

ip address:192.168.1.(any number b/w 2 to 254)
subnet mask:255.255.255.0
default gateway:192.168.1.1
primary dns:192.168.1.1

and also please tell how are you connected to your modem

your IP address must be 192.168.1.x where x can be any no. between 3-254(if connected through USB) or 2-254(if connected through LAN) & your gateway must be the home page address of modem which is 192.168.1.1 by default for almost all modems/routers.once you open the modem configuration page go to connection settings & just change the connection type/protocol from bridging to pppoe with rest of the values same.you will be asked to enter your bsnl username/password & after entering it will be stored in modem & will be used by modem to connect whenever you turn on modem.also enable DHCP in modem.

Hi,
I have a UTSTARCOM modem model no.Ut300R2U on a dataone connection.Is it possible to change the NAT Config on this modem type. If so , how??Also i tried visiting the 192.168.1.1 page and it requests a user name and a password to access the page. Is the username and password the same as my dataone username and password?

the default username and password for modem would be

username - admin
password - admin

OR

password - password

@trueblue

1. User Name is admin and password admin or password .
Please Try

2. In New model usually, in Advanced
only DMZ is available.
Post screenshot of Device status.

Example:
http://img523.imageshack.us/my.php?i...6096054bj6.jpg

3.If you use a dialer all ports are open. Use Anti Virus
and Firewall programs.

4. Download guide given below. for reference .


REF:1.
http://www.indiabroadband.net/attach...00r2u-v2.2.zip

REF:2.
UT-300R2U ADSL MODEM MENU

REF:3.
http://www.sumedh.info/articles/port...0r2u-bsnl.html

Further Reading :
http://www.indiabroadband.net/broadb...etting-up.html (UT300-R2U Ver 2.2 - Guide for setting up)

Thanks a lot.. .. that was very useful

deleted.

iam not able open 192.168.1.1

i have also the same problem with this modem..not able to open 19.168.1.1..but i can connect to net after dialing..how can i acces to modem config..?i saw that netbios over tcp ip is disable..