India Broadband Forum

rubin3330 · 06-09-08, 01:46 AM

My modem is smartAX MT841. now its in auto dialling mode. i wanna disable this auto dialling. then only i can use dial up connection to connect modem to internet.

I wanna change it to manual dialling mode, so that i can disconnect and reconnect using the bat files before free downloading b/n 2-8AM

So i need help to know how to change into manual dialling mode in the modem... i read modem manual and there is no sufficient info available abt it.

So please help me.

superprash2003 · 06-09-08, 06:56 AM

hope this helps Prashanth Speaks-Technology and Life: How to Setup bridged mode in UT300R2U steps are similar.. basically you need to go to the WAN page and change vpi/vci 0/35 to bridged mode

rubin3330 · 06-09-08, 11:42 AM

i done the following things.

i deleted all entries in connections>WAN configurations
created one with 0/35 and gave bridge mode.
then too i cant connect via dial up.
then i deleted dat and created 0/35 with PPPoE mode
this time also i was unable to connect.
i deleted tat too and create the same PPPoE with 0/32
this time i got connection, but its in auto dialling mode.

There is no default route setting option in the bridge mode in MT841
Also there is no option to edit the WAN type in a connection....
Whenever i wanna change im deleting the existing one and creating the new one. still now in auto dial mode.

is there any firmware update for MT841

waiting for the responses.
Thanks in advance

player · 06-09-08, 01:06 PM

There is no need to delete the connection...... just edit the connection

can you post some screenshots of your modem configuration as i am using a different modem so i cant tell you precisely.

player · 06-10-08, 12:07 AM

@vshnnair
the wizard option you mentioned is not available in every modem ............. are you aware of this

rubin3330 · 06-10-08, 02:07 AM

These are the screen shots of my modem. Its Huawei SmartAX MT841

Please look into it and tel me how to configure it for manual dialling.
Thanks for ur replies.

whitestar_999 · 06-10-08, 12:09 PM

default route option is only enabled in pppoe mode i think.still correct connection for bsnl is _0_35 with VPI/VCI values 0 & 35.in my opinion you have modified your connections too much.reset the modem by using "reset to factory default"option in modem or insert a pin in the hole at the back of modem & keep it pressed for 30-40 sec.make sure that during resetting power supply must be uninterrupted or else your modem will get damaged.after resetting start from beginning & edit the connection 0_35_ & change its mode to bridge.

06-09-08, 01:46 AM	#1
rubin3330 Junior Member Join Date: Jun 2008 Age: 23 Posts: 3 Rep Power: 0	Help me to configure MT841 for manual dialling My modem is smartAX MT841. now its in auto dialling mode. i wanna disable this auto dialling. then only i can use dial up connection to connect modem to internet. I wanna change it to manual dialling mode, so that i can disconnect and reconnect using the bat files before free downloading b/n 2-8AM So i need help to know how to change into manual dialling mode in the modem... i read modem manual and there is no sufficient info available abt it. So please help me.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
how to configure BSNL Type IV (MT841) modem for wireless setup with Netgear WG511T	hensum	BSNL broadband	4	11-15-09 04:01 PM
how to configure BSNL Type IV (MT841) modem for autodail and wireless setup.	India Broadband Internet	BSNL broadband	44	07-28-09 09:47 PM
Help Needed..Can we configure Huwaei MT841 Wi-fi router for MTNL Triband??	mayank_n	MTNL broadband	3	11-25-08 09:44 AM
Help to configure Huawei MT841 (BSNL Broadband) with Linksys wrt54G	dmns	BSNL broadband	0	01-05-08 10:48 AM
Help me to Configure SmartAX MT841	rohan_rdx	BSNL broadband	1	08-14-07 02:04 PM

06-09-08, 06:56 AM	#2
superprash2003 Platinum Member Join Date: Feb 2008 Posts: 2,692 Rep Power: 5	hope this helps Prashanth Speaks-Technology and Life: How to Setup bridged mode in UT300R2U steps are similar.. basically you need to go to the WAN page and change vpi/vci 0/35 to bridged mode

06-09-08, 11:42 AM	#3
rubin3330 Junior Member Join Date: Jun 2008 Age: 23 Posts: 3 Rep Power: 0	i done the following things. i deleted all entries in connections>WAN configurations created one with 0/35 and gave bridge mode. then too i cant connect via dial up. then i deleted dat and created 0/35 with PPPoE mode this time also i was unable to connect. i deleted tat too and create the same PPPoE with 0/32 this time i got connection, but its in auto dialling mode. There is no default route setting option in the bridge mode in MT841 Also there is no option to edit the WAN type in a connection.... Whenever i wanna change im deleting the existing one and creating the new one. still now in auto dial mode. is there any firmware update for MT841 waiting for the responses. Thanks in advance

06-09-08, 01:06 PM	#4
player Platinum Member Join Date: Jan 2008 Location: India, Bangalore Age: 19 Posts: 1,222 Rep Power: 3	There is no need to delete the connection...... just edit the connection can you post some screenshots of your modem configuration as i am using a different modem so i cant tell you precisely.

06-10-08, 12:07 AM	#5
player Platinum Member Join Date: Jan 2008 Location: India, Bangalore Age: 19 Posts: 1,222 Rep Power: 3	@vshnnair the wizard option you mentioned is not available in every modem ............. are you aware of this

06-10-08, 12:09 PM	#7
whitestar_999 Platinum Member Join Date: Jan 2008 Location: UP(west) Posts: 1,971 Blog Entries: 1 Rep Power: 3	default route option is only enabled in pppoe mode i think.still correct connection for bsnl is _0_35 with VPI/VCI values 0 & 35.in my opinion you have modified your connections too much.reset the modem by using "reset to factory default"option in modem or insert a pin in the hole at the back of modem & keep it pressed for 30-40 sec.make sure that during resetting power supply must be uninterrupted or else your modem will get damaged.after resetting start from beginning & edit the connection 0_35_ & change its mode to bridge.

India Broadband Forum

Help me to configure MT841 for manual dialling

Help me to configure MT841 for manual dialling

Similar Threads