Thread: port forwarding trouble

hello all,

i followed the PORT FORWARDING IMAGE TUTORIAL and seems i screwed upsometing,

i want to restore it to the earlier setting how to do it

here is the detail as it shows

Test the connection to your Internet service provider Test PPP server connection: PASS
Test authentication with ISP: FAIL
Test the assigned IP address: FAIL
Ping default gateway: FAIL
Ping primary Domain Name Server: PASS

also i dont have the green signal on my modem where it says internet

Reset your modem to default settings

how to reset the modem? anyhelp please

there are two ways to reset a modem either manually or through by the modems config. page , in modem's config. page click on the button which says restore to factory default settings or something similar.

When you are doing it manually just locate the reset switch in your modem and while modem is on just press and hold the reste switch until all the lights are off and you are done

NOTE: when you will reset your modem you will lost all the settings and you will not be able to connect to the internet

thanks for your reply, how to connect it back to the internet again, when you mean modem config page do you mean the dsl router page, i dont have any experience it this please let me know,


before that when i switch on my modem net used to connect, but now it pops us BSNL STATUS which asks for username and password

NOTE: when you will reset your modem you will lost all the settings and you will not be able to connect to the internet

please mention your modem model no

i think i am giving u the right details
Firmware Version: UT300R2U.0011.01
Hardware Version: UT300R2U 2.2
Model Name: UT300R2U


but the net speed is normal i am able to downld at 215kbs, have i done anything wrong?

which plan are you in if you are in H500 then you are getting very poor speed and if you are in H750 plan then you are getting pretty good speeds

NOTE: from the above which you have mentioned is the speed in Kbps (Kilo bits per second)
and when you download something from internet it is measured in KB/s(Kilo Bytes per second)

as you have said you are getting 215Kbps then your download speed will be 215/8 KB/s
...... now you must be wondering that why i divided 215 Kbps by 8 because i have converted the unit from Kbps to KB/s as 1Byte=8bits

i hope i am clear

hi player sorry its 215kbps the download speed and the net speed being around 1.7 MB,

the issue is is think i screwed up the dmz host setting as i didnt follow the tutorials correctly, i restored it to default, but usually ii switch on the modem and the net gets connected but now a bsnl status windows pops us and it requires username and password, when i enter them i am able to log in

also what is this

Test authentication with ISP: FAIL
Test the assigned IP address: FAIL

check this link & configure modem again---
http://www.calcutta.bsnl.co.in/datao...all/mdm04.html

hi,

thanks this is what i got in the usage section, can anyone let me know the exact meaning

Total Send Volume(GB) Total Receive Volume(GB) Total Volume(GB) Total Duration(hour) Sum Traffic Excluding Night Unlimited(GB)
0.06 1.008 1.068 7.84 0.046

Is it right that i have used .046 GB which means 46MB so far during the limited period?

from this link which option should i choose to reset my modem?http://www.calcutta.bsnl.co.in/datao...all/mdm04.html

click on "ADSL modem configuration" & a new page will open.follow the instructions & as for resetting read the last line---"press RESET at back by a ball pen refill for 10 sec on ON condition".

make sure that power supply is uninterrupted during this process.connect modem to UPS.

if i press the rest button, should it be connected to net or is it enough my system is switched onn?

would i need to install anything after resetting it? or would it be normal

disconnect from net first.keep the system on.you don't need to install anything but you have to configure the modem from start again.use the link i gave.

You could also try to configure using this guide: http://www.indiabroadband.net/bsnl-b...no-wizard.html (PPPoE Setup of UT-300R2U - Manual Method (No Wizard))

i recvd a CD can i use that CD to configure the modem? i dont feel comfortable with the manual method, sorry i am new to this.

it states for the wizard method click on RUN WIZARD where do i find it?

Your router's web interface may be different.

CD is for USB drivers and the PDF manuals etc. CD will not help you with configuration. The PDF manual will.

You have two options:

a) Do it yourself. You may struggle a lot but in the end you will become an expert and you may never face problems again (for configurations)
b) You can ask someone else (incl BSNL) to do this for you. When the problem comes again, you will face the same problems again.

i will choose the hard way do it myself

and in the link you gave for configuring the pics are not availabe

download the attachment which is a zip/rar file.it contains all the details.

Originally Posted by whitestar_999

download the attachment which is a zip/rar file.it contains all the details.

Originally Posted by saesms

i will choose the hard way do it myself

and in the link you gave for configuring the pics are not availabe

As whitestar_999 said, download the zip file.

Unzip the same to some folder. After unzipping, the folder that you chose will contain a file "PPPoE Setup of UT300R2U – Manual Method.htm" and another folder will be created as "PPPoE Setup of UT300R2U – Manual Method_files"

Double click on "PPPoE Setup of UT300R2U – Manual Method.htm".

i tried to follow the tutorial just4kix but it seems the versionis completely different, i am not able to do even step 3, so this is my version can anyone help me out please



Board ID: 96338L-2M-8M
Software Version: 3.08.02.UB.01.14_1357_100807
Bootloader (CFE) Version: 1.0.37-10.1
Firmware Version: UT300R2U.0011.01
Hardware Version: UT300R2U 2.2
Model Name: UT300R2U

can someone give me the bsnl broadband customer care number please... i am from chennai

Prashanth Speaks-Technology and Life: Port Forwarding In UT300R2U ADSL MODEM

that website requires username and password