Thread: Not able to access 192.168.1.1

With this 500C+ plan using WA3002G4 modem given by BSNL, I'm able to access internet after setting up the session by dialing up the connection. However, I fail to open up the page of 192.168.1.1.
Please can anybody help me with this?

Thanks,
Mahidhar

On XP, Click on Start --> Run --> Cmd

In the command window, run the command:

ipconfig/all

Post the results here.

My guess is that DHCP is off in your modem/router and TCP/IP settings' "Default Gateway" is not set. It must be set to 192.168.1.1.

You should assign your IP mannualy as 192.168.1.X. the subnet mask should be 255.255.255.0 and your default gate way should be 192.168.1.1. then you can access 192.168.1.1 page

Here is my ipconfig

Windows IP Configuration


Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 192.168.0.1
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :

PPP adapter Broadband:

Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 117.198.96.191
Subnet Mask . . . . . . . . . . . : 255.255.255.255
Default Gateway . . . . . . . . . : 117.198.96.191

Also, pinging the IP 192.168.1.1 doesn't work.....

Your modem IP address is http://192.168.0.1. Try that ...

am having the same problem too... a few months before i set my BSNL modem to work on "bridging" mode as per the instructions in this link:

http://www.indiabroadband.net/bsnl-b...er-wrt54g.html (Setup of ADSL Modem/Router UT-300R2U with Linksys Wireless Router WRT54G)

after that, everything was fine... i could use wireless internet. after this setup, i could initially open the BSNL modem page @192.168.1.1. but now i cannot. my router page is 192.168.2.1 which i can open. has this problem come because i changed the BSNL modem from PPPOE mode to bridging mode??

@ Mahikatti

Plz do as just4kix says that ur ip is http://192.168.0.1

because according to my knowledge as well, it is correct as per what ur network config has shown in cmd.

im not too sure about that..because his ipconfig output says ip address = "192.168.0.1" and gateway is blank.. that means his pc has the ip 192.168.0.1 .. that normally arises if you try to enabled ICS in windows.. or you might have inserted that manually by mistake..What you could do is go to control panel->network connection.right click on local area connection, click on properties then go to tcp/ipv4 properties.. there enter ip address as 192.168.1.10 and gateway as 192.168.1.1 .. should work now..

hmm good. lets hope one of those ideas we provided, helps him!!

My vote goes to Superprash. I think there is some problem with his IP setting. otherwise he should got 192.168.1.X IP

i have tried setting the IP to 192.168.1.1 and other settings that superprash suggested.. but internet stopped working altogether... so i had to revert to the old setting.

hi guys.. pls do have a look at my config and suggest me something.. now i have given direct connection.but before i had given to router.
these are the details.. pls help me.. this is draining me...

Code:

img137.imageshack.us/img137/9198/ipconfigid2.jpg

in your LAN TCP/IP settings(not BSNL network setting) enter IP address as 192.168.121.4 & subnet mask as 255.255.255.0 as both the values(169.254.x.x & 255.255.0.0) you currently have are wrong.