India Broadband

bshah2008@gmail.com

Hi Networking Experts,

I have a MTNL provided ADSL Modem/Router DSL-502T. It is currently set-up in PPPoE Mode. It is NOT in Bridge Mode.

I have a Linksys WRT54GS Wireless-G Router that I need to connect to the above mentioned modem/router.

A direct connection from Laptop to DSL-502T allows me to get on the internet.

If I add the Linksys router to the mix of things, I am not able to connect to the internet.

DSL-502T IP address = 192.168.1.1
WRT54GS IP address = 192.168.2.1 (I changed it from the default 192.168.1.1 after reading posts on several forums)

What are the settings that I need to change on the Linksys WRT54GS router so as to connect successfully to the internet? I have made sure that all the wires are connected properly, rebooted the routers several times)

Some forums I read said that I need to enable/disable DHCP. But I am not clear if I should do that on the MTNL or Linksys.

I am able to provide more info if you need it to help me.
Thank you in advance for your help.
-Bhavin

Admin

What is the version of firmware on your DSL-502T ?

You would need to upgrade to version 7.00.4 or later to get your setup working.

Upgrade your firmware and see if it works and if it doesnt please give us another shout.

Thanks

__________________
Reliance data card | Reliance broadband | Airtel broadband | Wimax

Admin

And thanks for posting all the model no's and specs ... its good to read your intelligently framed question otherwise half the threads here go like... Please help me my router is not working and thats it... Hope your problem gets sorted with this firmware upgrade

Some one please correct me if I am wrong.

Thanks

bshah2008@gmail.com

Current Firmware Version : V2.00B01T01.ML.20050530

When I checked to download the new version of the firmware, I came across this forum.

I may sound stupid, but can you direct me to the right place to download the 7.00.4 version as suggested?

I did visit D-Link Building Networks for People.. -> Choose Broadband, ADSL 2+, but they do not have DSL-502T listed. It has not been replaced by GLB-502T. Do you recommend that I download the firmware of this model?

Admin

Please ignore my firmware upgrade post. v 7.00.4 was meant for your wireless router not the mtnl modem. Dont worry about the firm ware as yet.. try the link below and see how it goes first.

This should sort out the issue : Networking a D-Link DSL502T with DL524 - Wireless - Networking

bshah2008@gmail.com

Hey Admin,
I am sorry, but I am not a networking person. I am not able to follow along with the instructions on the link that you have provided.
I did go ahead and disable the DHCP on the DSL-502T, but I am not able to set the static IP on Linksys. There are several options available on the linksys setup page and I am not clear which one I should tinker with.
I need more help.
Thanks,
Bhavin

lekhi123

In the starting i want to request to remove everything or in simple words just dismantle your network.

What i am keeping in mind that you are going to connect the system wireless. (Now if you are connecting the system with lan cable then connect PC and router. Remove all the network connections if any.)

1. Now connect the router and the modem and please make sure they both are switched off. This is necessary in both the wired and wireless case.

2. Once you are over with the first step, switch on the modem and let the modem be ready with all the lights.

3. Switch on the router and let all the LEDs to be there.

4. There is a CD given with the router, start installing the router with that. Now at any point if it asks you to select something like PPPOE, dynamic connection... please choose Automatic Configuration - DHCP. As this is required in case of all the ADSL Connections. Irrespective of you are using MTNL, Reliance or Airtel.

I think this will solve your problem as this is the simplest way of connecting.

Dont go onto the technicality of bridging mode/pppoe/DHCP mode.

Leave the things as it is... or

If you have changed, just reset everything to factory settings by pressing reset button for 5-10 sec.

Any problem or pange
we are happy to hear about

Chow!!!

sandy1980

Dear Admin,

I find it hard to believe that the step by step instructions given in CD didnot work...But the instructions given by you worked perfectly...

Thanks Again

Admin

Did Lekhi123's instructions work for you? if not give us another shout and I will try and create a more detailed tutorial with screen shots if I can manage to get hold of the gadgets involved.

Thanks

sandy1980

Yes Admin...Lekhi123's advise worked perfectly fine...I tried several times with CD instructions but didnt work...the instructions provided by Lekhi123 worked in first go....

Theres is a new problem now...Please advise if i should use a new thread for this...

The router works perfectly fine with the laptop connected to it...
but when i try to use the wireless facility i get problems..
The wireless adapter in my ACER laptop doesnt seem to be working...When i go to device manager and check...it is installed properly with the driver working fine...but the software that is installed in my computer which creates wireless network keeps saying that there is no driver installed...i tried installing the driver repeatedly from the CD provided with the laptop...still doesnt work...(please advise if i should use a new thread for this issue)

Thanks in advance