Thread: Need help in configuring WiFi Router for Reliance Broadband connection

Hi All,

Please help me to configure "Beetel 450 TC1" Wireless modem/router so that I can access my Reliance broadband connection thru wifi connection.

"Beetel 450 TC1" Wireless router does not have "WAN" Port at the back of it, it only has the port where you can hook up your telephone line. Hence, I am unable to use it in traditional way.

Upon contacting and googling, I came to know that Reliance broadband modems are bridged and the authentication happens over the portal in a web browser.

Please somebody guide me with complete set of steps so that I can configure it.

Thanks in advance.

Kaushal Mistry.

Ultimately I have resolved the above issue. I am now able to connect Reliance Broadnet using the above mentioned modem/router.

If anybody experiencing the same issue can take my help. Its an easy setup now.

Thanks,

Kaushal

congrats.
The thread is incomplete, without your solution.
You might have observed, in any forum, a solution if
effective is ALWAYS/MOSTLY
confirmed/posted by the thread starter
or by other contributers.

If you have not activated email notification in your USERCP
,any body wanting the solution, posting the request here
may not get response from you

PARA two:
Using the Reliance ADSL modem ( zx zte 831AII ??)
connect the computer normally. Then
the Rj45 from computer end to
LAN1 of Beetel 450BX.Then connect another Rj45 from Lan2 to computer.
WIFI will work for laptop.
Confirm.

Additional reference :
for similar modem/router/wifi with same hardware board.
http://www.indiabroadband.net/bsnl-b...reference.html (UTSTAR WA3002-G4 quick reference)

Hi ,

I am facing the same problem, if you give me the steps that would help me a lot.

Thanks in Advance.
Hari
(hariprasadid@yahoo.co.in)

Originally Posted by kaushalmistry

Ultimately I have resolved the above issue. I am now able to connect Reliance Broadnet using the above mentioned modem/router.

If anybody experiencing the same issue can take my help. Its an easy setup now.

Thanks,

Kaushal

hello pls pls help me to resolve. i hav reliance broadband. but want to use parallely in both lap and desktop. i hav beetel 450 tc1. but don't know to configure. my id tttreskarthik@yahoo.co.in

Originally Posted by karthiks

hello pls pls help me to resolve. i hav reliance broadband. but want to use parallely in both lap and desktop. i hav beetel 450 tc1. but don't know to configure. my id tttreskarthik@yahoo.co.in

You have to use PPPoE mode instead of Bridge mode.

if you need step by step instructions
select WA3002_g1 menu from
web site Calcutta Telephones

http://www.calcuttatelephones.com/da...all/mdm08.html
A link with screenshots also available. will post if needed.
http://www.maharashtra.bsnl.co.in/ssa/nashik/wa3002.htm
In router select "Always On" PPP/PPPoE
enable DHCP and give a range .
In computer
TCP/Ip properties
obtain Ip address automatically both in Desk top and laptop.
Feedback.

how to select "always on" ppp/pppoe? i don't know anything.
did u remember anything regarding beetel 450 tc1 wat kausal shared in this site.

Modem wifi router WA3002-G1
Did you check the Maharastra link given , which has screen shots of this modem/router.?
or the step by step instructions given in Calcutta telephones web site ?
Simply PPP/PPPoE option is selected in WAN
page of a modem. Enter your UserID/PW etc.
If you select 'Bridged" THEN you have to
use a "Dialer" externally and enter userID/PW
everytime you want to connect to Internet.

Confirm how you connect now .

hi, thanks for ur response. i hav went through those sites. but in reliance they did not provide any modem. they jus gav MTA6328-1be2s. i don't know wat it is. but the matter is, i'm gettin ethernet cable from outside(from main connection) not the telephone line.
this kit gives telephone line and ethernet(lan 1 and lan 2) output. in reliance they hav user id and password. at a given time only one computer can login. no sharing is possible.

same problem need to know step by step procedure for wifi setup for reliance

i have beetel 450 Bx1 wifi router

regards rohit
dr.rohit@yahoo.com

Originally Posted by kaushalmistry

Hi All,

Please help me to configure "Beetel 450 TC1" Wireless modem/router so that I can access my Reliance broadband connection thru wifi connection.

"Beetel 450 TC1" Wireless router does not have "WAN" Port at the back of it, it only has the port where you can hook up your telephone line. Hence, I am unable to use it in traditional way.

Upon contacting and googling, I came to know that Reliance broadband modems are bridged and the authentication happens over the portal in a web browser.

Please somebody guide me with complete set of steps so that I can configure it.

Thanks in advance.

Kaushal Mistry.

@Nagar0001
1.Please confirm whether you got any adsl modem from Reliance.

2 Please see this thread .
http://www.indiabroadband.net/bsnl-b...tml#post208783 (UTSTAR WA3002-G4 quick reference)
Beetel 450BX is same as Utstar WA3002-G4
Chennai link has screen shots.
You can try "DIALER" mode first.
Then try WIFI.
( Usually we need "Always On" PPP/PPPoE connection,
but in Reliance it seems not possible.
3.
Select "Bridged "in wan page.
In lan page enable DHCP.
Try.
Feedback.
4.
Confirm you have Windows 7 operation system for another method.
http://74.125.153.132/search?q=cache...ient=firefox-a

Hi friends. . .

looks like i have a different version when compared to the screen shots in the thread. . . .

i have beetel 450TC1 ADSL2 + router. . . and a reliance connections.

as in the thread there is not lan input port it has only a telephone jack....

can some one help me configure them and get my wifi working. . . i need step by step instructions pls. . . . .

i have checked all the links in this thread and the other threads assoiated but looks like it has the older version . . . .

can some one pls help me. . .

Regards
me

@met_eros

i have beetel 450TC1 ADSL2 + route

This will be an adsl modem+4lanport+wifi and can be connected to Reliance Telephone line via an adsl splitter.
For settings refer WA3002_g1 in link No 8 Calcutta Telephones
( see first link given below ).
Help menu may be missing.
Also
http://mtnldelhi.in/services/con_s.doc
feedback.

2. Confirm your connection is broadband and Telephone connection combined.
3.
Feedback copy/paste
ipconfig /all for wireless lan card settings.

When you say adsl splitter, i need to buy some thing like a adapter???

is that what ur saying

Hi i did try as per the instructions. . .

1) no luck. .
2) in the bot in the router page it says ppp password invalid thought its correct
3) there is no setting u requested in cmd
4) it is telephone & bb connection, but both r in different rooms

not able to upload snap shots b cos of the file size. . . will do it later today or tomorrow. . . .

5.Procedure:
START RUN type cmd
Ok
New window
type ipconfig /all
copy/paste data for both LAN and WLAN .
6.
Additional reference with screenshots.
http://www.maharashtra.bsnl.co.in/ssa/nashik/wa3002.htm
report if link not available.
7.
See post No 3 also. for reliance vpi/vci 0 and 35.

8.. Reliance must have supplied an adsl splitter. The PHOne in different room can be
connected to PHONE port . If not supplied . buy additional adsl splitter for the phone.
Rj11 to modem port can go direct tp Reliance Phone junction.

i have tried both the responses. . . .


this is the first one i get after following the first steps . . . .
thought the password is correct it get the error in the last ine

Device Information
Firmware Version : TM4-0Q-007
MAC Address :
LAN
-------------------------------------------------------------------------

-------------------------------------------------------------------------

-------------------------------------------------------------------------

IP Address : 192.168.1.1
Subnet Mask : 255.255.255.0
DHCP Server : Enabled
WAN
-------------------------------------------------------------------------

-------------------------------------------------------------------------

-------------------------------------------------------------------------

Virtual Circuit : PVC0PVC1PVC2PVC3PVC4PVC5PVC6PVC7
Status : Not Connected
Connection Type : PPPoE
IP Address : 0.0.0.0
Subnet Mask : 0.0.0.0
Default Gateway : 0.0.0.0
DNS Server : 0.0.0.0
NAT : Enabled
ADSL
-------------------------------------------------------------------------

-------------------------------------------------------------------------

-------------------------------------------------------------------------

ADSL Firmware Version : FwVer:3.10.30.0_TC3085 HwVer:T14.F7_5.0
Line State : Showtime
Modulation : G.DMT
Annex Mode : ANNEX_A

-------------------------------------------------------------------------

-------------------------------------------------------------------------

-------------------------------------------------------------------------

Downstream Upstream
SNR Margin : 19.5 8.0 db
Line Attenuation : 5.5 1.0 db
Data Rate : 8064 864 kbps
Attainable Rate : 12620 960 kbps
Out Power : 9.5 12.0 dbm

-------------------------------------------------------------------------

-------------------------------------------------------------------------

-------------------------------------------------------------------------
CRC Down/Up(db) : 0/ 1
HEC Down/Up(db) : 0/ 0
Adsl Status : PPP PASSWORD INVALID

when i change the vpi/vci to 0 to 35 i get the follow error . . .

Error Message:

-------------------------------------------------------------------------

ERROR: FAIL TO UPDATE DUE TO... Duplicate to a VPI/VCI !


-------------------------------------------------------------------------


pls help

This is exactly the screen i go though. . .

hope this is off some help

since i am not allowed to post url

http: // www . pcwintech . com / screenshots-beetel-450tc1-beetel-firmware

remove the extra space dude

hi
i have a utstarcom modem supplied by bsnl i want to connect it to my system for reliance broadband connection all leds are on led ,dsl and status led is blinking...but my internet connection is fail it shows page cannot b displayed
i want a solution to connect to internet as well i want to use wifi also plz help me soon

\here are modem details
utstarcom---model no wa3002g4
features : 4eth+1wifi 802.11g adsl2+router

@sayeed_cs
Unit :utstarcom---model no wa3002g4
1. Please refer first link below.
VPI/VCI for RELIANCE 0 AND 35.
Use DNS supplied by Reliance or open dns 8.8.8.8
and 208.67.220.220
2.
Copy/paste following data ( no edit ) for LAN/WLAN connection only.

START RUN type cmd
OK
type ipconfig /all
3.
Feedback

Originally Posted by essbebe

@sayeed_cs
Unit :utstarcom---model no wa3002g4
1. Please refer first link below.
VPI/VCI for RELIANCE 0 AND 35.
Use DNS supplied by Reliance or open dns 8.8.8.8
and 208.67.220.220
2.
Copy/paste following data ( no edit ) for LAN/WLAN connection only.

START RUN type cmd
OK
type ipconfig /all
3.
Feedback

plz let me see the snapshots...and can u plz tel hw to do frm start

Please see screen shots in Link No 1 or step by step instruction/s in other link/s.in wa3002_g4 given below.

2. Reset the modem to factory settings and try Dialer mode.
Enter your userId and PW in computer window
( reset switch/access canbe in the rear or bottom right side
small hole. press with ball pen refill for about 15 to 20 seconds. )

3. Copy/paste ipconfig /all

Originally Posted by sayeed_cs

plz let me see the snapshots...and can u plz tel hw to do frm start

hello i still cant connect to internet using that utstarcom modem for my reliance broadband plz help out

Unit :utstarcom---model no wa3002g4
1. Please refer first link below.
VPI/VCI for RELIANCE 0 AND 35.
Use DNS supplied by Reliance or open dns 8.8.8.8
and 208.67.220.220
Please check the link WA3002-G4 for maximum info, screenshots, step by step instructions.
You have not even checked this link given in above post.
Chennai Telephones- Changing password in DataOne Pre-configured modem
or the MP link etc.
.
2. Feedback. TRY ethernet Rj45 connection first.
Then wifi mode.
COPY/PASTE data here.
Procedure
START RUN type cmd
OK
new Window
Type ipconfig /all

I'm having a binatone DT840 wifi...
haw to configured the reliance broad band connection in this wifi..
already i tried to configure but i cant able to do this
plz help me........
please.....

Need Device info or connection page screen shot.
Post as annexure jpg here.
Check screen shots given in link/s below.
Confirm at least lan connection is ok.
Mention the Adsl modemdetails used ahead of Binatone dt840.