Thread: How to configure Binatone DT845W for reliance bb

Thanks vahid...essebbe...it worked finally.

Dear VAHID,
thanks a lot for your procedure on confg of Binatone modem DT 845W. i was able to connect to internet just by reseting the modem and entering all data in PVC0. there was no requirement of firmware change.
regards
raja

Originally Posted by vahid.alavi

@essbebe: Thanks for the quick reply.
I could configure it this way and it worked. So I post it for others to be able to use as well.

1. Reset the router. (There is a reset button in back of the router, hold it for 10 to 13 seconds using a pin. The router diods(lights in front panel) will go off except the Power; router will restart)

2. open your browser and in the address bar type 192.168.1.1

3. The pop up window asks for a username and a password. By default it is 'admin' for the username and 'password' for the password. (you can check the bottom of your router for the default username and password).

4. When you logged in, on the top menu, select:

interface setup -> Internet

5.look to the left side of the page and find 'ATM VC' section and find the 'virtual circuit' in its right.
select pvc1, when page is loaded, make its status(below of the 'virtual circuit') and make it deactive. now save your work by clicking the save button at the end of the page. Do the same for the rest except pvc0.

6.select pvc0, make sure that its status is set to 'activated'. If not select it.

7. By default VPI is set to 1. Change it to 0.

8. By default VCI is set to 32. Change it to 35.

9. ATM QoS is UBR

10. PCR should be 0 indicating UBR without PCR.

11. Find 'Encapsulation' Section at the right of the page. In that section at its right, find 'ISP' and set it to 'Dynamic IP Address'. and let page to reload.

12. At the 'Dynamic IP' section find 'Encapsulation' and set it to '1483 Bridged IP LLC'.

13. You don't need to change anything more, just save your work.

14. on the front panel of the router, the internet light should be on.

15. now go to reliance login page. Worked?

after this part "At the 'Dynamic IP' section find 'Encapsulation' and set it to '1483 Bridged IP LLC'."


you need to check the bridge more in "Dynamic Ip Section"

and you need to enable DHCP server as well


got mine fixed this way

thanks brother,i m facing same problem.you have put nice question.its so much helpful to me.

What is posted is STANDARD setttings for any adsl modem.
As the menu page/s are different, new users find it difficult .
If you check my sig link wa3002_g4 /beetel450TCI you have a choice of
(a) step by step instructions as given here
(b) screen shots
(c) video
(d) Flash mode etc.
Always refer the manual, if in doubt.
Usually once the modem is set and working, there is no reason to go on changing the parameters.
Better to SAVE /backUP present settings
( either done by BSNL or user) to revert back to a working condition.

Originally Posted by essbebe

Confirm:
(a)
Your Reliance Broadband connection is landline based and you are using an ADSL modem ( mention make/model/number) supplied by Reliance.
(b)
In Binatone there are 8 default VCO's 0 to 7. each with different
VPI/VCI for instance VCO2 can be 0 and 35 ( common to BSNL and Reliance)
Confirm VPI/VCI for Reliance BB connection.
(c)
With Factory defaults , you can try a Dialer
and try to log in with ID/PW is system ( wanminiport )
if connected to internet then try wifi settings.
(d)
If Binatone was earlier supplied by /used for Airtel FW
may have to be changed.
(e)
For actual working settings ( less wireless) for my BSNL
connection see screen shots here. ( similar 110TCI)

Thanks dear, for share the information. i do agree with you dear..................