Thread: How to configure Binatone DT845W for reliance bb

Hi,
I tried everything to make my binatone DT845W to be able to connect to internet. I have reliance broadband connection.
I am trying to setup a wifi but, with the Binatone router I am even not able to connect to internet by wire.
Is there anyone has the same router? How to configure it for reliance. Reliance technical department is not a use.

Confirm:
(a)
Your Reliance Broadband connection is landline based and you are using an ADSL modem ( mention make/model/number) supplied by Reliance.
(b)
In Binatone there are 8 default VCO's 0 to 7. each with different
VPI/VCI for instance VCO2 can be 0 and 35 ( common to BSNL and Reliance)
Confirm VPI/VCI for Reliance BB connection.
(c)
With Factory defaults , you can try a Dialer
and try to log in with ID/PW is system ( wanminiport )
if connected to internet then try wifi settings.
(d)
If Binatone was earlier supplied by /used for Airtel FW
may have to be changed.
(e)
For actual working settings ( less wireless) for my BSNL
connection see screen shots here. ( similar 110TCI)

@essbebe: Thanks for the quick reply.
I could configure it this way and it worked. So I post it for others to be able to use as well.

1. Reset the router. (There is a reset button in back of the router, hold it for 10 to 13 seconds using a pin. The router diods(lights in front panel) will go off except the Power; router will restart)

2. open your browser and in the address bar type 192.168.1.1

3. The pop up window asks for a username and a password. By default it is 'admin' for the username and 'password' for the password. (you can check the bottom of your router for the default username and password).

4. When you logged in, on the top menu, select:

interface setup -> Internet

5.look to the left side of the page and find 'ATM VC' section and find the 'virtual circuit' in its right.
select pvc1, when page is loaded, make its status(below of the 'virtual circuit') and make it deactive. now save your work by clicking the save button at the end of the page. Do the same for the rest except pvc0.

6.select pvc0, make sure that its status is set to 'activated'. If not select it.

7. By default VPI is set to 1. Change it to 0.

8. By default VCI is set to 32. Change it to 35.

9. ATM QoS is UBR

10. PCR should be 0 indicating UBR without PCR.

11. Find 'Encapsulation' Section at the right of the page. In that section at its right, find 'ISP' and set it to 'Dynamic IP Address'. and let page to reload.

12. At the 'Dynamic IP' section find 'Encapsulation' and set it to '1483 Bridged IP LLC'.

13. You don't need to change anything more, just save your work.

14. on the front panel of the router, the internet light should be on.

15. now go to reliance login page. Worked?

Congrats.
Please update thread , when wifi also enabled/configured by you.

There are not too much left to configure Binatone DT 845W and with a very easy steps I could configure the wifi. I explain it down.

1. Make sure that activated is selected for 'Access point settings' section -> 'Access point'.
'Channel' set the channel to the country you live in. In my case, it is 'India'. and select 'Auto' from the box to its right.
In this section you don't need to change anything more and the default set up is well defined.(If you need let me know that I update the post.)

2. In the section 'Multiple SSIDs Settings', select 1 for SSID number.(SSID is called as Service Set Identifier, and it is used to set up different types of network. If it is for home use, 1 SSID is sufficient.)

Set the 'SSID Index' to 1.

For 'Broadcast SSID' select 'Yes' is you want the name of your SSID to be visible to every one or set it to know, if you want it hidden. If it is hidden, then you require to input 'SSID' and the key(a kind of password) from the wireless network connection section of your operating system. I prefer it to be visible for the ease of work.

In 'SSID' box, you can type any name you like. This name will appear in your wireless connection list. For example I used 'WLAN' which is a short for Wireless Local Area Network.

Next in this section is 'Authentication Type' which is very important. Each one has its own protocol which makes the key/password secure from the hackers. For home users, select WPA2-PSK which stands for 'Wi-Fi Protected Access - Pre-Shared Key'. It is stronger than the rest excluding the enterprise.

3. In section 'WPA-PSK' in the left side of the page, you can find 'Encryption' to its right. There are two types of encryption algorithms defined. TKIP and AES.
Some operating systems (Generally old versions of windows) has problem with AES encryption. But not TKIP. Select either of AES or TKIP. For example AES for me worked better and I know it is more secured than TKIP.

Below that 'Pre-Shared key' box is there. That is the place where you define a key i.e a password which you will use in your operating system to connect to the router. It should not be less than 8 character and should not exceed 63. (The instruction is given in the right-hand-side of the box)

4. Find the section 'WDS Settings' and make sure that 'WDS Mode' to its right is set to off.

5. Find the section 'Wireless MAC Address Filter' in the right hand side and make sure that 'Active' to its right is set to 'Deactivated'.

6. Save the work, and your router will restart. If not, let the page reload and then, restart your router manually.

7. Turn on your pc wifi, select the SSID you defined, Enter the key/password and press connect from your operating system wireless networks list.
You should be able to connect to internet with no problem.

Originally Posted by RCOMcare

Hi Vahid,

This is to inform you that your concern has been noted and our team is eager to resolve it. Please provide us with your phone number on which we can reach you. In future, you may also write to us at............with all the details.

Regards,

RCOMcare

hehehe, you are kidding, don't you?

Regards

hehehe, you are kidding, don't you?

Probably @RCOMcare did not notice, that you could do the settings for Binatone all by yourself, without any help from this forum too!!!
and was only posting instructions for other members benefit !!!

They have read only your first post!

Hi,
I tried everything to make my binatone DT845W to be able to connect to internet. I have reliance broadband connection.
I am trying to setup a wifi but, with theBinatone router I am even not able to connect to internet by wire.
Is there anyone has the same router?How to configure it for reliance. Reliance technical department is not a use

Originally Posted by essbebe

Probably @RCOMcare did not notice, that you could do the settings for Binatone all by yourself, without any help from this forum too!!!
and was only posting instructions for other members benefit !!!

They have read only your first post!

@essbebe: I think so; They don't read, the same they don't listen on the phone. lols

Hi Vahid,

Thank you for this thread. I was using airtel and switched to Reliance a week back (as i shifted residence where airtel did not cover). Since then i've been requesting the reliance customer care and technical support to configure my DT 845W. Finally yesterday they connected me to the technician who very rudely told me that the modem is airtel specific and will never work with Reliance or BSNL and if i intend to use this connection, i'll have to use it with the wired modem only.

In my desparation i was browsing through similar forums when i came acroos your thread and it worked like magic. All i had to do was to change the VCO settings as the rest was already in place.

Thanks once more.

I think it's high time RCOM should take note of the customer concerns and pathetic tech support team they are employing.

Thanks,
S Dutta.

Originally Posted by SDutta

Hi Vahid,

Thank you for this thread. I was using airtel and switched to Reliance a week back (as i shifted residence where airtel did not cover). Since then i've been requesting the reliance customer care and technical support to configure my DT 845W. Finally yesterday they connected me to the technician who very rudely told me that the modem is airtel specific and will never work with Reliance or BSNL and if i intend to use this connection, i'll have to use it with the wired modem only.

In my desparation i was browsing through similar forums when i came acroos your thread and it worked like magic. All i had to do was to change the VCO settings as the rest was already in place.

Thanks once more.

I think it's high time RCOM should take note of the customer concerns and pathetic tech support team they are employing.

Thanks,
S Dutta.

Glad that it worked for you. Yeah, you are right. Reliance Customer Care is very bad. They are so rude and no sense of responsibility. That's sad.

BTW, if the way you configured the router is different from mine, please leave a post. Might someone like us needs it.

-
Regards
Vahid

Originally Posted by SDutta

Hi Vahid,

Thank you for this thread. I was using airtel and switched to Reliance a week back (as i shifted residence where airtel did not cover). Since then i've been requesting the reliance customer care and technical support to configure my DT 845W. Finally yesterday they connected me to the technician who very rudely told me that the modem is airtel specific and will never work with Reliance or BSNL and if i intend to use this connection, i'll have to use it with the wired modem only.

In my desparation i was browsing through similar forums when i came acroos your thread and it worked like magic. All i had to do was to change the VCO settings as the rest was already in place.

Thanks once more.

I think it's high time RCOM should take note of the customer concerns and pathetic tech support team they are employing.

Thanks,
S Dutta.

Hi,

This is to inform you that your concern has been noted and our team is eager to resolve it. Please provide us with your phone number on which we can reach you.

Regards,

RCOMcare

Thank for sharing above details,,,
I've been saved by you guys... finally my beetel 450TC1 modem is working on wire... however still there is an issue with the wi-fi connectivity. I'm not sure what the issue is... I'm able to connect to router but don't get internet access.. can any one help.. even the reliance login page is not accessible. I've dynamic IP and it's working fine with LAN

Regards,
Rajesh

Your PM.
check in your Wlan network settings wifi SSID AIRTEL or MNGMT appears.use key 0987654321.
( remove Lancable from laptop ( If windows 7 Os not needed )
feedback.

I'm gud with the wifi connectiity. I'm able to connect to this modem as well using WLAN. issue is I can't access any website using IE or firefox. Error message on diagnose says there is issue with DNS setting.

Regards

Laptop( Master)

Condition One :
Rj45 from Reliance direct to Laptop
you can log in with relianceID/PW in browser.
Internet connected . can surf.
confirm.

Condition Two:

Reliance cable Rj45 to Lan 1 of Beetel 450TCI
Lan2 to laptop ethernet port.
same as above.
connect to Internet and surf
confirm

Condition three :
with set up as in (2) above
( Presume MAC filter has been disabled )
Wif ssid appears in another laptop. or phone
Use ssid key
(a)can access Internet and surf.
(b)Cannot access Internet
(c) browser: log in page appears.
(d) in laptop master wifi access OK. surfing OK.
(e) any other : error message.

Para two:

Laptop or Desktop

As you have selected 1483 bridged mode, DNS will be selected
by modem autmatically ( Reliance DNS)
In Network settings LAN WLAN
Ip address and DNS : select automatically. Apply Save.

Feedback. item wise. see signature link Beetel 450TCI.

Post as screen shot STATUS Device info.

for use in forum
http://www.indiabroadband.net/comput...tml#post315289 (Monitor Screen Shot)

I'm trying my best to keep it simple, my ans to ur reply above is condition three (b). Further:
I've Reliance wired braodband, I'm using Beetel 450TC1 model+router, I've dynamic IP, I'm able to connect to internet using LAN(after reliance user id/paswd), I can access modem/router using wifi(I'm able to connect it)
Only issue is internet does not work when it try it on Wifi,,, even after first starting the connection with LAN and switching over to wifi. I've attached screen shot as much as possible. Let me know if u need more information

Thanks for help in advance

Beetel450TCI needs a RJ11 ( telephone cable ) input
to function normally.
The cable from Reliance ? is it Rj11 ? or RJ45 ?
Are you provided a telephone also ?

Condition 1:
Confirm this .
NO modem involved. Not supplied by R.
RJ45 cable direct from Reliance to your laptop ethernet port.
You are given a USERID/PW and log-in, in your Browser.
You have no control over this connection.
No changes can be made.

confirm.

Dynamic IP address
Is this ALWAYS same for you enter in address bar to log in ?.

feedback.

Para two:
In old set up change Channel to 11 and disable Mac address filter.


Since you have Windows 7 download application Connectify
and instal in laptop. ( becomes an AP for other systems )
Check WIfi works in any other laptop/smartphone.

Cables are all fine.
condition 1. find data below


C:\Users\Speedster>ipconfig/all

Windows IP Configuration

Host Name . . . . . . . . . . . . : Speedster-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Wireless LAN adapter Wireless Network Connection 2:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter
Physical Address. . . . . . . . . : 8C-A9-82-4F-CD-69
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes

Wireless LAN adapter Wireless Network Connection:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Intel(R) WiFi Link 1000 BGN
Physical Address. . . . . . . . . : 8C-A9-82-4F-CD-68
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet
Physical Address. . . . . . . . . : 60-EB-69-EC-97-7F
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::8dcc:5adb:2669:62b3%13(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.1.2(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : 14 September 2011 10:56:44
Lease Expires . . . . . . . . . . : 17 September 2011 21:17:11
Default Gateway . . . . . . . . . : 123.236.56.1
192.168.1.1
DHCP Server . . . . . . . . . . . : 192.168.1.1
DHCPv6 IAID . . . . . . . . . . . : 291564393
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-15-18-17-67-60-EB-69-EC-97-7F

DNS Servers . . . . . . . . . . . : 192.168.1.1
NetBIOS over Tcpip. . . . . . . . : Enabled

Condition 2

"1483 Bridged" is selected

For your consideration "internet works with LAN", "Wi-fi connection is established" "internet doesn't work with Wi-fi"

From POST No 12
I've been saved by you guys...
finally my Beetel 450TC1 modem is working on wire...
however still there is an issue with the wi-fi connectivity.
I'm not sure what the issue is... I'm able to connect to router
but don't get internet access.. can any one help..
even the reliance login page is not accessible.
I've dynamic IP and it's working fine with LAN

.
123.236.56.1 Gteway
INDIA MAHARASHTRA NAVI MUMBAI
DSL RELIANCE COMMUNICATIONS LTD RCOM.IN

From POST NO 18.
"1483 Bridged" is selected ( *OR DYNAMIC IP)
[For your consideration "internet works with LAN",
"Wi-fi connection is established" "internet doesn't work with Wi-fi"

Please post STATUS device info. page.

thanks for all the technical info... i'm now an enlighted person with some more IT terms.... finally everything is working now.... the issue was that WIFI setting for IP in my laptop was manually updated... I've set it to automatic and it worked...

@yanky-y

Congrats.
Still need Device info status page. for thread completion.
Now if ..your wifi is working with LAN cable connected to Laptop.
disconnect it for final confirmation.

LAN is disconnected... working fine

how to provide you device info status page??

post this page.http://www.indiabroadband.net/attach...1&d=1316025337

Here you can find the same attached

Thanks . noted for future use.