India Broadband

samueldotj

I got TataIndicom WiMax connection yesterday with static IP.
I tried to connect to the Starmax SS using telnet 192.168.1.1/2 but it is not connecting. I also tried opening URL http://192.168.1.1. But it is not connecting. How somebody guide me on this.

Thanks
Sam

babraham

This is only a basic Setup. You can change the values according to your wish and for more security. I have Initially tried with a Dlink router and it worked fine...The configuration is simple and straight forward in Dlink Router but I preffered a Cisco Router and purchased a LinkSys WRH54G model.

Follow the instructions from the router manual to change the Router Settings. Connect the cable from the PoE box "Data IN" port to the routers "Internet" port (Blue Port). Connect the LAN cable from the Ethernet Port (marked 1 - 4) behind the Router to your PCs network Card (RJ45 Interface). Once your Wireless link is UP you can remove this cable. Change the computer IP to 192.168.1.20 with default subnet mask. Open Internet Explorer and type http://192.168.1.1 (this is the default IP address of Linksys router)

--------------------------------------------------------------------------

Click WAN icon
Enter the username and Password (refer the manual for Username & password)

Select "Setup" from top Left corner

Enter the Values given by the service provider for the "Basic Setup"

INTERNET SETUP (e.g.)
Internet Connection Type : Select "Static IP from the drop down list"
Internet IP Address: 121.243.x.x (your Static IP provided by VSNL)
Subnet Mask: 255.255.255.x
Gateway: 121.243.x.x
Static DNS 1: input the first DNS IP address provided bythe service provider
Static DNS 2: input the Second DNS IP address provided by the service provider


Optional Settings
Leave this field as it is


NETWORK SETUP
Router IP
Local IP Address : 192.168.1.10
Note: remember this IP address. Next time you have to type http://192.168.1.10 to access the router configuration page.
Subnet Mask : 255.255.255.0

Server Settings (DHCP)
DHCP Server : Select "Enable"
Starting IP Address : 192.168.1.100 (Select Default Value - Avoid starting from 192.168.1.1)
MAC Binding : Dont change anything here.
Maximum Number of DHCP users: 50
Client Lease Time : 0
Default gateway : 0.0.0.0
WINS : 0.0.0.0

Time Settings
Don’t change the default settings

Don’t change the default values of "DDNS", "MAC Address Clone", "Advance Routing" and "WAN Port Configure" unless your are familiar with these settings.

--------------------------------------------------------------------------

From the Top Select "Wireless"
Basic Settings
Wireless network Mode : Mixed
Wireless Network Name (SSID) : MyNetwork
Wireless Channel : 6 - 2.437GHz
Wireless RF Control : Standard
Wireless SSID Broadcast : Enable
Wireless RF Scheduling : Disable
Wireless Security
Security Mode : WEP
Default Transmit key:1
WEP Encryption : 64 bits 10hex digits
Pass phrase : leave Blank and input a valid Hex key in the key 1: field
key 1: abcdef1234 ( Dont put this value - Jumble the characters and remember this value)

Leave MAC Filtering and Advance Settings

-----------------------------------------------

Leave "Security", "Access Restrictions” and "Applications and Gaming" with the default values.

---------------------------------------------

Click on Administration from the "Management Option" and change the Router Password . Enable Wireless Web management Access and disable Remote management. Leave all other settings with their default Values.

-----------------------------------------------

Click on “Save Settings” at the bottom. This will save the configuration and will reinitialize the router. You will loose the connection to the router at this time. Take the TCP/IP properties of your computer and change the settings to “Obtain an IP address automatically” and “Obtain DNS address automatically”. Reboot the Computer and verify the computer has obtained an IP from the router DHCP Lease.Type “ipconfig /all’ at command prompt to check this. To access the Router configuration page again type http://192.168.1.10
------------------------------------------------------------------------
If your PC/Laptop is not configured for a wireless connection, install the appropriate driver and enable the connection or take the help from the vendor. At this time you can remove the Input the key which you have entered in the router configuration page (Under Wireless security - key 1: ). To configure the Starmax box, refer to some other links given elsewhere in this thread. If you experience any problem, Switch off PoE, Router and computer. Reboot PoE first, Router second and computer third

bharath_india

whats the max with this connection ?

babraham

This is a 256kbps plan and on an average I am getting 230kbps. It all depends on the signal strength and quality of the signal at your place.

gpganesh

Hi Bala,

1. I am having reliance Wimax in KR PURAM since Dec'07. I would have happily used it only for 1 month in TOTO. Planning to shift to Tata. Can u suggest about the performance.

2. I need the contacts for getting a new connection.

3. How much do they charge initially.

Ganesh
gpganesh@gmail.com

gpganesh

Hi Sam,

I wanna go for a new connection at KR PURAM. Need to know the contacts for approaching. and the cost details.

Can you please update me on this front.


GANESH
gpganesh@gmail.com

samueldotj

Hi Ganesh,

Sorry, I just saw your reply.

I dont have any contact details, you can get one from the tata indicom site.

price: I paid around 4.5K as advance payment for 4 months and got free 3 months offer. IIRC the monthly amount is 1000 + tax.

Sam

gardencityboy

now that 3 months free offer is not there any more
you pay 4 months advance and the installation change is waved off

aks1981

Hi,

I need to setup the PPPOE mode and connect my wireless router to the modem. I too am not able to connect to the starmax modem. Telnet says "could not open connection on the port 23". I ran a port scanner on the box which found that both port 23 (telnet) and SSH are blocked. How to login to the modem now?

Please help ASAP.

Thanx !!!

cyberbaba

To login to configure the Telsima antenna do the following;-

1. set pc ip to 192.168.1.10 (anything but 192.168.1.1)
2. Open a browser type http:\\192.168.1.1
3. ID root and pwd is telsimawl

Let me know if it works.. It does for me .. I Got a Telsima 2105 antenna and a Power-Dsine POE box... POE and PPPOE are 2 different things so pls confirm.

Cheers
Nik