How to connect Huawei SmartAX MT882 modem to Netgear wireless router WGR614v7?

I have the following setup components:
- Huawei SmartAX MT882 modem from BSNL dataone broadband
- Netgear wireless router WGR614v7
- Windows XP desktop (P4, 3.2GHz)
- Windows XP laptop (Intel centrino M 1.8 GHz)

My connection/configuration works fine from the modem directly to the desktop/laptop. I am able to access internet. Now, I need to connect the modem to the wireless router so that I can surf the net from both laptop and desktop. I am not able to do it.
I have tried the following, but these do not work:
- tried the Netgear wizard setup
- tried the steps exactly as in:
http://www.indiabroadband.net/bsnl-b...ork-guide.html
- tried myself to configure the modem and router with no luck

Can you kindly help in this regard?

□ Connect u r modem's RJ45 cable directly into the uplink port of the w.router.

□ Connect ur pc's network port to one of the lan port of the w.router.

□ If laptop is wireless then ur w.router will automatically detect after configuration.

□ If u need it wired then connect a similar cable to a free lan port of the w.router from the laptop's ethernet port.

Now open routers IP Address through internet explorer ... type http://192.168.1.1

Use admin for username and password for password and continue configuration. Go for a PPPoE Connection

Try all this after resetting ur router. Power on and press reset for 20 - 30 seconds. Turn off and turn on.

i have the same situation and after 12 hours of serious attempts , connection to internet fails...
will let you know in case i succeed, and request the same off you..

good luck.

I have similar setup.
- Huawei SmartAX MT800 modem + BSNL dataone broadband
- Netgear wireless router WGR614v7
- Desktop: Windows XP/Linux, with 2 network cards. [connected to Router by wire]
- Laptop:Windows XP laptop [Connected wireless]

Internet is working fine, from both the systems. But I couldn't access each other's shared folders. Simply, LAN is not working.

Before buying the Wireless router, I used a crossover cable to connect the computers for sharing internet & exchanging files.

Now with my netgear wireless router, apart from sharing internet connection, Is it possible to wirelessly network my desktop and laptop to exchange files etc?

Any help is greatly appreciated.

Cheers,
Raguanu

try my above setup .... if it doesn't work i'll help you

Originally Posted by coolday

try my above setup .... if it doesn't work i'll help you

I haven't tried connecting the laptop to router using cable. I'll try that.

BTW, laptop is detecting wireless connection and Internet is working perfectly fine. It's just that I couldn't make the computers talk to each other.

Thankx.

Remember all systems should be in the same workgroup... alsp do the network setup wizard .... Try pinging both ways ...
If Ip address is set to automatic option then goto command prompt and type ipconfig /all to know the ip address of that particular system and then ping .....

Thanks coolday.

The issue is resolved now. I came to know I had disabled some network related services in my desktop. Once I enabled them everything is working fine.

Thanks for the help.

Hi Ani

are you able to resolve this problem? I am also facing this problem for more than 6 months, and not getting any support. pl help me if you find a solution

@karthi25

I am also facing this problem

@ani posted only one message almost two years back.
You want him to respond ? 25-07-2007
@coolday has suggested solution. did you try ? 20-10-2007
@raghuanu solved the problem 26-11-2007

Now for six months you did not get a solution.
Explain your set up again,
modem make/model wifi router make model etc
and say
where you are getting stuck?

All contributers may not read
old posts,to understand your problem.

Or
Check "Broadband How to... " forum.
Give feedback.

modem 192.168.1.1 WGR614V6 192.168.2.1
Ethernet adapter Wireless Network Connection 2:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Wireless Notebook Adapter
MN-720 #2
Physical Address. . . . . . . . . : 00-0D-3A-6B-A8-D4
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 192.168.2.2
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.2.1
DHCP Server . . . . . . . . . . . : 192.168.2.1
DNS Servers . . . . . . . . . . . : 208.67.220.220
208.67.222.222
Lease Obtained. . . . . . . . . . : Sunday, February 08, 2009 6:08:42 A

Lease Expires . . . . . . . . . . : Monday, February 09, 2009 6:08:42 A

Hi

I have a NETGEAR ADSL2 MODEM (DM111P) and subscribed BSNL broadban in chennai. Modem is configured as PPOE connection and internet works fine if I connect my laptop with modem (via cable).

Later I bought a wireless router (Netgear WGRR614v7). I configured (used the wizard also followed the steps shared in manual / forums here). but dont get internet connectywhen i connect the laptop via router (wired / wireless).

I see one problem here as the router wizard detects Dynamic IP address (type of internet connection) instead of PPoE.
My modem IP : 192.168.100.1
DCHP = ON
Subnet mask = 255.255.255.0
ADSL Setting :
VPI = 0; VCI = 35
protocol =PPoE Bridging
MTU Size =1492

Router setting :
IPaddress = 192.168.10.1
Get dynamic IP address
Get DNS automatic
MAC = default

Download this . with screen shots etc.

India Broadband Forum

OR

Otiose Banter: Airtel Beetel Modem + Netgear WGR614 Wifi Router

check this blog for guidance.
Dm111P settings seems OK.
Hintsa) In TCP/IP obtain IP address automatically.
in both desktop and laptop.
(b)Enable DHCP in modem. What is the range you have given?
(c) try modem in "alwayson" Mode " PPP/PPPoE not bridged.
Compare Ip address''s given in my earlier post.

You can attach pictures etc as annexure.
when posting click "Go Advanced"